Peak 44 Bastion Pad Adapter

[RWT]

I should have time to get mine ordered this week

 

[randy66]

I’ve only sent out 3 so far, nothing fit up so far but one is probably only now arriving. I’m assuming it’s the same recoil pad, but we should be able to check the profile. I can send you an image file that can printed 1:1 and then wrapped on the black tooth stock to see if they match up.

Would you be willing to share the image file with me? I have a black tooth and would love to do a test fit. Thank you!

 

[Bbrinks]

Would you be willing to share the image file with me? I have a black tooth and would love to do a test fit. Thank you!

Of course. I’m out of town for work, but will be back tomorrow night. I’ll put a 1” reference in there too just to make sure it’s printed at the correct scale.

 

[Bbrinks]

FYI for the curve. The line is 5” for scale

 

[randy66]

FYI for the curve. The line is 5” for scale

Thank you!

 

[Battle]

It’s awesome that you’re doing this for guys, but sad that it’s needed. I just toured the Weatherby factory yesterday and was thinking they really need to change the recoil pad system.


Sent from my iPhone using Tapatalk

 

[Klooop]

Kind of a goofy cutout into the stock. I would have liked a flat end, rather than needing an adapter like this (nice work by the way!).

 

[wind gypsy]

Just posting to give kudos to @Bbrinks - Very nice solution you've created.

 

[Thermos]

Just fit mine up. Hardest part is getting the old recoil pad off. Everything else was easy. LOP came out at 13-3/4 as requested. Tikka superlite in Bastion 5.36 lbs bare rifle with this adapter.

This looks really good. What is the exact type of recoil pad you are using? Size, thickness?

Today I have a Tikka with Blacktooth stock that I use as a lightweight hunting rifle. It is sub 3kg complete with scope and suppressor. I think it is perfect for mountain hunting, but a little too short LOP for prone shooting.

Now that I see it`s possible to change the LOP, I want to set up my other rifle for prone shooting with a Bastion stock. I want to lengthen the LOP with 35-40mm. Not sure if that is possible with the adapter and a recoil pad, or if I need an extended version of the adapter.

Can you measure from A to B like this picture?
Want to figure out all the details before I order a stock.



@Bbrinks can you ship to Norway?

 

[AZ Gator]

I just wanted to write a short post that I have one of these LOP extension adaptors from @Bbrinks and it is exactly what these Bastions needed.

Removing the old pad is permanent, as it will get torn up when removed, but it wasn’t as difficult as I initially thought it might. I used a razor to trace along the carbon stock edge and each pass cut a little deeper. Initially, I just tried cutting about 1/8” deep thinking I might be able to slide out the old pad and preserve it. That won’t happen, so just keep gradually cutting deeper and deeper until it can easily tear/break off. Then I used pliers to grab the inside edges of the pad left inside the stock and pealed pieces off the inside of the stock. I then used a dremel to remove the old epoxy to give a flat surface for the adaptor to slide in to, and epoxied the new adaptor in.

This is definitely what the Bastion needed (not as much as a proper recoil pad design to better allow for LOP adjustments, but here we are).

 

[2buffalo]

This looks really good. What is the exact type of recoil pad you are using? Size, thickness?

Today I have a Tikka with Blacktooth stock that I use as a lightweight hunting rifle. It is sub 3kg complete with scope and suppressor. I think it is perfect for mountain hunting, but a little too short LOP for prone shooting.

Now that I see it`s possible to change the LOP, I want to set up my other rifle for prone shooting with a Bastion stock. I want to lengthen the LOP with 35-40mm. Not sure if that is possible with the adapter and a recoil pad, or if I need an extended version of the adapter.

Can you measure from A to B like this picture?
Want to figure out all the details before I order a stock.

View attachment 1072007

@Bbrinks can you ship to Norway?

Microcell Ultra-Light Recoil Pad

Microcell Ultra-Light Recoil Pad

www.hastingsdistribution.com

I can measure it tonight.