Painless Load Prep (Precursor to Painless Load Development)

[huntnful]

I have had the exact opposite experience with Peterson. 6.5PRC, 7PRC and 30-06 necked down to 25-06 or up to 35 Whelen has been great. I also have had great luck with Lapua in 6.5 Creed and 300PRC. Plus in a really hot load the Peterson and Lapua brass lasts a lot longer. Which is nice if you have a caliber for which you need to fire form, 25-06AI in my case, where the primer pockets only last 2 or 3 firings in lesser brass.

I actually enjoy proper brass treatment. To me the real focus is simplified load development. Modifying Form's process a bit the following works for me.

1. Load a pressure ladder test going up from a little below where the load data says the velocity you'd be happy with to a grain or two over max. Seat at .03 off the lands if magazine allows.

2. Shoot the ladder test. Stop when you hit pressure signs you are not comfortable with.

3. Load 10 with the powder charge in the middle of the best grouping of your ladder test.

4. If the 10 shot group is .75 MOA or better, done. If not move on to another bullet or powder.

I may be fooling myself into thinking this is a good process, but it works for me. Plus I want to do a pressure test anyway because I want to know where my max load is.

I’ve shot a lot Peterson with no issues as well. Same with ADG. But I’ve still had issues with both. Just giving examples. I’ve shot A LOT of Lapua, with zero issues or inconsistency. And so far Alpha seems to be consistent as well. But I haven’t shot near as much of that.

 

[Torque]

So, I've read the painless load development several times and now I've read the painless reloading thread.

Correct me if I'm wrong in my summary.

Painless Load development: Pick a bullet. Pick a powder charge, close to max, that will give you the velocity that you want. Seat the bullet to your magazine and/or close to the lands (how close/far doesn't matter) If it doesn't shoot well, just randomly pick something else and repeat the process.

Painless Reloading: Don't worry about cleaning, just resize and load brass up until it won't chamber, then throw it away and get some new brass.

Are these summaries correct?

 

[Andouille]

I’m here to learn. How do you size in a way that reduces brass growth?

Bump shoulder back only 2.5-3 thou, rather than the 8-10+ thou required to get back to unfired factory brass length. As some mentioned you need some clearance in case dust or grit enters your chamber, or if your sizing is off a thou or two. You can use scotch tape on the back of the case to test clearance, one layer is 1-1.5 thou thick. I like my rounds to just barely chamber with two layers of scotch tape on the case head.

 

[wind gypsy]

Another thing when you’re sizing the initial piece of brass to get a proper shoulder bump (or just making it fit in your chamber), you should use a new piece each time you’re adjusting the die. If you keep resizing the same piece, and just bumping it further and further and further until it’s correct, it’ll actually be much harder and have more spring back.

So when you grab another piece, you’ll actually bump it more than that initial piece that you spent all that time setting up

I have never considered this, always just used one piece (with expander removed) to set bump. This probably explains some of the issues i've had getting it consistent. Good tidbit.

 

[wind gypsy]

So, I've read the painless load development several times and now I've read the painless reloading thread.

Correct me if I'm wrong in my summary.

Painless Load development: Pick a bullet. Pick a powder charge, close to max, that will give you the velocity that you want. Seat the bullet to your magazine and/or close to the lands (how close/far doesn't matter) If it doesn't shoot well, just randomly pick something else and repeat the process.

Painless Reloading: Don't worry about cleaning, just resize and load brass up until it won't chamber, then throw it away and get some new brass.

Are these summaries correct?

On the cleaning front, you still dont want lube on the brass. I think the idea is that it doesn't need to be spotless/shiny and a little carbon on it isn't a problem. I dont clean before sizing unless brass is filthy but definitely clean lube off after sizing. I dont see tumbling in rice as a nuisance compared to wiping off cases with rags.

Picking a spot close to max from go - Takes understanding of what influences pressure and familiarity with some cartridges IMO otherwise i would do the 1 shot ladder for velocity pressure first.

Ex: i'm pretty confident how much H4350 in Lapua brass for a new 6.5 creedmoor to start with. Give me ADG brass (likely different capacity than lapua) and a powder i've never used and i'm not going to just take a load manuals published max as the gospel especially when manual data uses different brass.

 

[huntnful]

I have never considered this, always just used one piece (with expander removed) to set bump. This probably explains some of the issues i've had getting it consistent. Good tidbit.

I learn everything the hard way lol. Spend 10 minutes getting a perfect .002 bump, then grab another “fresh” piece and it bumps .005. WTF? lol


So just use a new piece after each adjustment, then once it’s dialed, grab all the pieces you used while setting the die and run them through one more time. They’ll be good enough.



Also: tighten sizing dies with a wrench. They can come loose when you’re half way through sizing a batch of brass and you won’t catch it and they won’t even bump the shit.

 

[Torque]

On the cleaning front, you still dont want lube on the brass. I think the idea is that it doesn't need to be spotless/shiny and a little carbon on it isn't a problem. I dont clean before sizing unless brass is filthy but definitely clean lube off after sizing. I dont see tumbling in rice as a nuisance compared to wiping off cases with rags.

Picking a spot close to max from go - Takes understanding of what influences pressure and familiarity with some cartridges IMO otherwise i would do the 1 shot ladder for velocity pressure first.

Ex: i'm pretty confident how much H4350 in Lapua brass for a new 6.5 creedmoor to start with. Give me ADG brass (likely different capacity than lapua) and a powder i've never used and i'm not going to just take a load manuals published max as the gospel especially when manual data uses different brass.

I've reloaded for over 20 years. I clean my brass after every firing and after every lube application. Is it 100% necessary? I'm sure it's not, but it's how I like to do the process. I have a dedicated press (a cheap Christmas discount Lyman) with a dedicated depriming die. I do not use that press for anything else.

I haven't always done that, but I can see a significant difference in my reloading presses and dies. Now that I keep my brass clean, my press rams stay clean and my dies stay clean and debris free. Which, in my mind at least, keeps things more consistent in my ammo production. I had large batch of 45 ACAP and 9mm brass I was processing one day. After around 250, the ram on my press froze in place from all of the carbon/primer residue the cases were losing. I usually do much smaller batches of rifle ammo, but that day showed me exactly how quickly and easily that stuff builds up. So, I keep the brass clean on the other processes. All I'm losing is a little time. I do all of my reloading in the evenings so processing everything at night and overnight doesn't really lose me anything.

 

[Formidilosus]

So @Formidilosus for the budget guys like myself, of the "normal" brass such as Winchester, Federal, Hornaday and Starline.
Which would you chose to be good brass in your experience?

I use all of them. I don’t really care. Probably Hornady last, but I really don’t care.

 

[NWBLKTAIL]

I learn everything the hard way lol. Spend 10 minutes getting a perfect .002 bump, then grab another “fresh” piece and it bumps .005. WTF? lol

Cannot count the amount of times I have lived out that scenario at the reloading bench

I read the use a different piece for setting the sizing die post and smacked myself in the forehead. That makes Perfect sense, thank you

 

[huntnful]

Cannot count the amount of times I have lived out that scenario at the reloading bench

I read the use a different piece for setting the sizing die post and smacked myself in the forehead. That makes Perfect sense, thank you

Yes sir! I did it many times myself as well.

 

[HuntHarder]

FWIW, I clean before I size. I think it keeps your dies nice and clean and makes for a smoother operation. Not needed, but I prefer it.

 

[Nine Banger]

Also: tighten sizing dies with a wrench. They can come loose when you’re half way through sizing a batch of brass and you won’t catch it and they won’t even bump the shit.

Yup. Get sloppy and you get to pull bullets somewhere down the line.

School of hard knocks here too.