Painless load development (mine)

[Formidilosus]

BR-4

Not that many failures. Maybe 1:100,000… or more.

Are you loctite your bolt handle is all the way down each shot?

Have you cleaned the bolt out and the firing pin off?

What are you using to seat the primers?

What cases? And did you trim them?

 

[lak2004]

What's the preferred primer seating device? I've got the frankford arsenal hand tool and have had some issues with seating depth and disfigured primers. Had 2 failed firings 2 years ago on a deer hunt. 3rd one was the charm and put the buck down thankfully, but would like to switch to something better.

 

[Matt5266]

I've only ever used a rcbs hand primer. Everything from 300 wsm down to 223 and all handgun calibers. Never had a single fail to fire in any of my reloads.

 

[9487329]

Are you loctite your bolt handle is all the way down each shot?

short answer no, but I’ve got the UM short w/ ball and I try to be cognizant of that, it’s definitely down when I recock it

Have you cleaned the bolt out and the firing pin off?

Doing that now

What are you using to seat the primers?

RCBS hand primer

What cases? And did you trim them?

Assorted reloaded factory:
Hornady frontier, black hills tmk, fiocchi .556, federal gmm, and some new starline

I did have to use a primer pocket hand tool to remove the crimp and open the pocket because the primers wouldn’t seat without it on some.

 

[Formidilosus]

short answer no, but I’ve got the UM short w/ ball and I try to be cognizant of that, it’s definitely down when I recock it

Ok. That is the most common reason for fail to fires.

Doing that now

Good.

RCBS hand primer

Good

Assorted reloaded factory:
Hornady frontier, black hills tmk, fiocchi .556, federal gmm, and some new starline

I would pick one good make and stick with it while you figure it out- stareline is fine.

I did have to use a primer pocket hand tool to remove the crimp and open the pocket because the primers wouldn’t seat without it on some.

Yep. I would stick with one type to narrow the issue down.

 

[Castle Rock]

Cases that are sized too much is a common issue

 

[9487329]

Cases that are sized too much is a common issue

All done reloaded 1-2 times

 

[nm.otter]

Small base dies?

 

[Harvey_NW]

I've only ever used a rcbs hand primer. Everything from 300 wsm down to 223 and all handgun calibers. Never had a single fail to fire in any of my reloads.

Only issue I've had is with the shellholder version leaving the cups proud and causing resistance on close, the universal version has seemed to be more consistent and haven't had issues in the last couple hundred rounds.

 

[Quandary]

What's the preferred primer seating device? I've got the frankford arsenal hand tool and have had some issues with seating depth and disfigured primers. Had 2 failed firings 2 years ago on a deer hunt. 3rd one was the charm and put the buck down thankfully, but would like to switch to something better.

In May I started using the Derraco PCPS Primer Seater. It a pretty inexpensive way to easily set the primer depth and crush you want. The tool is amazingly consistent. Since I started using it my primers are all seated +/- .0005 from target. Whether that level of consistency makes any difference on target is debatable but it has tightened up my ES and SD numbers, It is also very easy to use and fast.

 

[Nine Banger]

In May I started using the Derraco PCPS Primer Seater. It a pretty inexpensive way to easily set the primer depth and crush you want. The tool is amazingly consistent. Since I started using it my primers are all seated +/- .0005 from target. Whether that level of consistency makes any difference on target is debatable but it has tightened up my ES and SD numbers, It is also very easy to use and fast.

I like this one too if I have a bunch of brass sized. It takes a minute to set up. Almost needs its own press.

If I'm just screwing around I still use a hand primer.

 

[lak2004]

In May I started using the Derraco PCPS Primer Seater. It a pretty inexpensive way to easily set the primer depth and crush you want. The tool is amazingly consistent. Since I started using it my primers are all seated +/- .0005 from target. Whether that level of consistency makes any difference on target is debatable but it has tightened up my ES and SD numbers, It is also very easy to use and fast.

Thanks I'll check it out!

 

[MCGHeel]

What's the preferred primer seating device? I've got the frankford arsenal hand tool and have had some issues with seating depth and disfigured primers. Had 2 failed firings 2 years ago on a deer hunt. 3rd one was the charm and put the buck down thankfully, but would like to switch to something better.

Got a Hornady versaprime gonna fire up this weekend if I get the chance. Assembly looks pretty nice. Should be a good upgrade over hand primer and I think will dial in nice and consistent


Sent from my iPhone using Tapatalk

 

[Matt5266]

Only issue I've had is with the shellholder version leaving the cups proud and causing resistance on close, the universal version has seemed to be more consistent and haven't had issues in the last couple hundred rounds.

Interesting. The shell holder version is the one ive always used. Never an issue. I didnt even know they were making a universal . That looks pretty handy though. I hate switching out shell holders on that thing.