OG Suppressor Early Access Rokslide Link

[Ajsomp]

Stopped by my FFL to file and take a look- was pleasantly surprised to find a golden ticket in there!

Happy early Father’s Day to me. Looking forward to getting in the class next year
@Unknown Suppressors @Shoot2Hunt

 

[Styer22]

Welp, with everyone’s coming in I finally couldn’t resist any longer and gave in. Happy father day to me!

 

[D R T]

Approval process started.

 

[2Stamp]

Mine's been at my SOT since Monday; we got the eForm submitted this morning. Heading in to the Post office to mail my fingerprint cards this afternoon.

I got the bead blasted finish and I like the way it looks.

 

[Q_Sertorius]

Mine (#1222) just got approved! On my way to get her now, even if it means working late tonight.


____________________
“Keep on keepin’ on…”

 

[BjornF16]

Picked up my can from ATF jail today 10 days after certification (NFA trust)...guy at the counter was all excited and said "there's a golden ticket in there for you"...I be like, stop pulling my leg (and how do you know about the US golden ticket?).

Looks like another US can in my future......what should it be?

PS- thanks @Unknown Suppressors !!!

 

[Wprinkle]

What is the minimum clearance required between the OD of the barrel and ID of the suppressor? At the thread end shoulder it is .726, four inches back the OD is .775. The ID of the reflex end of the OG is .800... is that close enough to cause interference during the shot process?

It is an ACE #2 barrel cut to 18 inches for reference.

 

[Harvey_NW]

What is the minimum clearance required between the OD of the barrel and ID of the suppressor? At the thread end shoulder it is .726, four inches back the OD is .775. The ID of the reflex end of the OG is .800... is that close enough to cause interference during the shot process?

It is an ACE #2 barrel cut to 18 inches for reference.

That tight of clearance will probably affect your harmonics and push your nodes all over and you won't be able to tune your load to get Optimal Barrel Timing for 1/4 MOA groups.

JK, I don't believe in any of that voodoo. I doubt it will be an issue as long as the can is torqued on properly. Somebody should test it though, jam a twig in between the ID and barrel and see if it causes a POI shift.

 

[Formidilosus]

What is the minimum clearance required between the OD of the barrel and ID of the suppressor? At the thread end shoulder it is .726, four inches back the OD is .775. The ID of the reflex end of the OG is .800... is that close enough to cause interference during the shot process?

It is an ACE #2 barrel cut to 18 inches for reference.

Nope. You’re fine.

 

[Okie_Poke]

The $100 off sale has me sorely tempted. Tbh I was sorely tempted before. Need to find a local FFL/SOT that doesn't charge an arm and a leg for the transfer though.

 

[Scottyboy]

The $100 off sale has me sorely tempted. Tbh I was sorely tempted before. Need to find a local FFL/SOT that doesn't charge an arm and a leg for the transfer though.

Call around. Mine used to charge $100 for the transfer now they do $50, or free, as the wait times are basically nil so they are not “warehousing” them. I’m a trust and was cleared in 12 days.

 

[Q_Sertorius]

The $100 off sale has me sorely tempted. Tbh I was sorely tempted before. Need to find a local FFL/SOT that doesn't charge an arm and a leg for the transfer though.

The gun store I use doesn’t charge any fees. I think they just like to see the cans come through. I try to buy some of their ammo or a spare magazine whenever I get a new can through them, but they don’t seem to care either way. Good group of guys. I drive about 30 minutes extra to go to their store because the closer store’s fees are outrageous.

I would look around and see if driving a little further saves you the fees.


____________________
“Keep on keepin’ on…”