Measuring Blackhorn 209 by volume vs weight

[Pooch]

I'm kinda new to muzzleloaders so be gentle, I have CVA Accura and planning on using the 209 powder with 250 gr. Powerbelt ELD's on elk. I have read a bunch of threads and am a little confused. Can I just use a volume say 100 grains to start and work up or down to get best accuracy? TIA

 

[swavescatter]

Best accuracy = weigh each charge. Density/packing fraction varies lot to lot.

Edit - and start a lot lower than 100 grains. My CVA LR/X with Arrowhead LRMP plug shot 75 grains really well.

 

[MuleyFever]

Yes you can. Your rifle manual should also list the max load they say is safe. The Blackhorn site also has info on loads.

 

[bigsky_hunter]

I buy plastic medical vials off eBay and weigh each charge. I then have a bunch of pre weighed available.I use 77gr by weight, iirc that equals 100 gr by volume. Blackhorn has table listed on their website with conversion.

 

[elkivory]

I'm kinda new to muzzleloaders so be gentle, I have CVA Accura and planning on using the 209 powder with 250 gr. Powerbelt ELD's on elk. I have read a bunch of threads and am a little confused. Can I just use a volume say 100 grains to start and work up or down to get best accuracy? TIA

You'll probably get lots of comments on this, so here's mine based on reading multiple online discussions addressing this process. I've decided to do 10 samples by volume, then weigh and average from each batch (canister) I use. Last night I took a sample of 10 from a canister I've been using for a couple of years. I measured 100 volume and my average weight was 69.88. Highest weight was 71.1 and lowest was 69.10. I was not super careful on filling my volume measuring tool. Another kicker I read couple of days ago is roll the canister if it has been transported, because finer granules could settle and cause inconsistent velocities. Whenever I'm going to shoot, I will weigh my charges mostly because I have the time and it might make things a little more consistent.

 

[elkivory]

I buy plastic medical vials off eBay and weigh each charge. I then have a bunch of pre weighed available.I use 77gr by weight, iirc that equals 100 gr by volume. Blackhorn has table listed on their website with conversion.

I'm pretty sure it's 100 volume equals 70 weight. I took this off Hodgdon website. Answer to FAQ, can I weight BH209.
"Yes. If you prefer to weigh charges, you can convert the volume load recommendations into weighed grains by multiplying the volume load by 0.7. Example: 100 units by volume x 0.7 = 70 grains by weight. 110 volume charge x 0.7 = 77 grains by weight."

 

[ElDiablito]

This is one of the most common questions among new shooters. The short answer is, as long as you’re consistent in your method, you’ll see no dispersion difference in weighed vs volume measured Bh209 charges. If you’re going to volume measure, get yourself a good brass volume measure like this one.



When Bh209 first hit the market, the volume to weight conversion factor was .7. However, with the current lots, it is more like .801. It has gotten slightly heavier. So a max charge (for example) of 120 gr volume of Bh209 will weigh 96.1 gr weight.

Here’s the current load data:

https://hodgdonpowderco.com/wp-content/uploads/2024/08/2023-MDATA.pdf

More importantly, a 250 gr Powerbelt is undoubtedly one of the worst choices you could possible make for an elk bullet. Too soft and light!!

 

[WCB]

I use a brass measure like above. I try to fill it the same and make sure the top is tight...it will work itself loose and not "cut" the powder right at the top.

Shooting some where in the 90s by volume depending on what MZ I'm using with the brass tool my groups out to 200yards are way more than acceptable. Just for kicks I am going to weigh some and see how or if my groups improve to the point that it is worth the extra time.

 

[bigsky_hunter]

I'm pretty sure it's 100 volume equals 70 weight. I took this off Hodgdon website. Answer to FAQ, can I weight BH209.
"Yes. If you prefer to weigh charges, you can convert the volume load recommendations into weighed grains by multiplying the volume load by 0.7. Example: 100 units by volume x 0.7 = 70 grains by weight. 110 volume charge x 0.7 = 77 grains by weight."

You’re right, thanks for clarifying. Was just going off of memory and wasn’t home to check my notes. Fwiw I use 77gr by weight and get good accuracy with 250 Barnes tmz out of an omega. I get around 2000 fps.
To the OP, you are going down the right path by using BH209 to begin with.

 

[Scoggin12]

My recommendation is load a volume measure and pour on a powder scale a few times. Then shoot those same loads at a target. You will load by weight every time after that I promise.

 

[Pooch]

Thanks for replies. next question what is a good brand for powder scale?

 

[ENCORE]

Thanks for replies. next question what is a good brand for powder scale?

Scales & Accessories - Hornady Manufacturing, Inc

Scales & Accessories...

www.hornady.com

Amazon.com : digital reloading scales for powder grains