Leupold VX6-HD gen 2 - Return to Zero

Joined
Jun 15, 2025
Messages
7
I’ve read a lot on here regarding tracking/RTZ on gen 1 scopes. The gen 2 VX6 line supposedly has beefed up internals from the Mark series, so I was hoping the tracking issues were corrected. Maybe they were, and there maybe a problem with my setup.

Mounted the new VX6 gen 2 on a Browning XBolt 2 7PRC. It was zeroed at 100 yds and has been excellent holding zero. I’ve been very satisfied after 50 rounds. That is, until I did a quick dial test. The scope tracked correctly as I dialed up in 5 MOA increments. The problem came in when I returned to zero at the zero-stop lock. Sensing there was a problem, I did several more controlled tests after sighting in at 100 yds each time. The results were repeated each time I did the test.

On the left is the gen 2 mounted on the 7PRC. The right is a gen 1 VX-5HD mounted on my reliable 7mm-08. The numbers represent the order of shots in each string:

IMG_6469.jpeg

Before I make a call to Leupold, I am looking for input to rule out scope mounting issues. I have both scopes mounted with Burris Signature Zee rings on a one piece rail, torqued to specs. I do plan on swapping the scopes on the two rifles when I have time to rule this out. Pics of the gen 2 mounted on the 7 PRC:


IMG_6478.jpeg

IMG_6475.jpeg

IMG_6476.jpeg

Any ideas before I start a repair claim?
 
The top cap for your front ring doesn't look right. Seems uneven gap front to back and something sticking out the back at the top of the tube. Those rings are also less robust than id use. Even still, it's probably the scope.
 
Get rid of those rings and get something that has some grip. I had a scope slip in them on a smokeless muzzleloader a few years ago.
 
I’ll need to remount the scope for sure. This rifle has been holding zero fine as long as it is not dialed up and back down.

The other rifle with the gen 1 on it has the same rings and returning to zero fine.

Could it be a warped rail possibly? I’ll know for sure once I find the time to swap scopes.
 
So you have the 7mm-08 intentionally zeroed low and right at 100 yds? That's what it looks like to me.

Have you fired 10 or 20 shot groups with the rifle? Just curious. If not, any of those 100 yds shots look like they could be part of a larger round count group.

The PRC also looks like it's tracking off to the right as you go up.

I think you need to shoot more groups with more than 3 rounds to get correct data.

If you're shooting Hornady factory ammo, there's lots of stories with consistency issues in the 7mm PRC ammo.
 
I don’t see anything blatantly wrong with your mourning set up but I don’t trust those Burris rings at all but then again I don’t trust the vx5 and 6 line either. In nightforce I trust.
 
So you have the 7mm-08 intentionally zeroed low and right at 100 yds? That's what it looks like to me.
I was shooting with a bipod. For some reason my shots always go a bit low and right with that rifle. If I plan to use the bipod for hunting, I re-zero.

If you're shooting Hornady factory ammo, there's lots of stories with consistency issues in the 7mm PRC ammo.
I found that out the hardway. Chrono SD’s were rediculous. Switched to Federal real quick.
 
I am definitely going to take the advice here and try new rings first. Any recommendations appreciated.

What I don’t understand is that the same results shown were repeated. In other words, when the gen 2 didn’t return to zero, I re-zeroed it again and repeated the test. It tracked up satisfactorily again in 5 MOA increments up to 15 MOA, and then on RTZ, got hung up on 10 MOA. The setup has held zero prior to this testing, but dials weren’t touched.

So the type of rings could effect the erector internals when dialing?
 
I am definitely going to take the advice here and try new rings first. Any recommendations appreciated.

What I don’t understand is that the same results shown were repeated. In other words, when the gen 2 didn’t return to zero, I re-zeroed it again and repeated the test. It tracked up satisfactorily again in 5 MOA increments up to 15 MOA, and then on RTZ, got hung up on 10 MOA. The setup has held zero prior to this testing, but dials weren’t touched.

So the type of rings could effect the erector internals when dialing?

I already told you the scope is probably the problem. You're selectively reading responses.
 
Back
Top