Easton Sonic 6.0

Joined
Sep 28, 2018
Messages
2,233
Location
VA
Anyone using them? Their gpi seems very reasonable 9.5 gpi on a 250 spine VS 11.7 gpi on the 5mm axis . Its a little bigger diameter but would eliminate the need for all the "extra" heavy inserts and collars
 

Joe Holden

Lil-Rokslider
Joined
Mar 14, 2019
Messages
188
Location
Kansas
They're next up on my list. Mirror the GPI of the Victory RIP TKO's I'm currently using but would allow for standard inserts (either aluminum or brass) like you mentioned.

Haven't looked at OD measurements between the two but can't imagine they're incredibly far off.
 

OCHO505

Lil-Rokslider
Joined
Aug 11, 2013
Messages
241
Location
Albuquequer, NM
I loved the concept but why they took a great arrow and made it .006 straightness is beyond me. I am sure it will still fly fine but was poor choice IMO. I am using Spartans currently, which I like a lot!
 
  • Like
Reactions: ATL
Joined
Sep 6, 2022
Messages
27
Anyone using them? Their gpi seems very reasonable 9.5 gpi on a 250 spine VS 11.7 gpi on the 5mm axis . Its a little bigger diameter but would eliminate the need for all the "extra" heavy inserts and collars
Been playing around with these for a few months. They seem like good arrows to me. Went from 250 spine FMJ's to these and it took my arrow from 524 to 422 grains. Sure shortened my sight tape a lot too. I will say with the light arrow my bow sounds much louder than before. Also feel longer shots seem a little more inconsistent out around 80-110 yards.

shooting a Hoyt Ventum 30 29" draw at 80lbs
 

CowboyD

FNG
Joined
Jul 23, 2022
Messages
37
I recently tried them, and they are a great light gpi arrow. After watching videos showing little difference in penetration of heavy slow arrows compared to light fast arrows, I've changed to light fast arrows to gain the trajectory advantage.
 
OP
D
Joined
Sep 28, 2018
Messages
2,233
Location
VA
I recently tried them, and they are a great light gpi arrow. After watching videos showing little difference in penetration of heavy slow arrows compared to light fast arrows, I've changed to light fast arrows to gain the trajectory advantage.

you need "adult" arrows to see the difference #ranchfairy
 

three5x5s

WKR
Joined
May 21, 2013
Messages
1,173
Location
Central Ky.
FEATURES:

  • 6mm ST Inserts included (18 grains)
  • 6mm reduced-diameter higher-velocity 100% carbon-fiber construction
  • Factory helical fletched w/ 2” Blazer Vanes
  • Pre-installed 6mm nocks
  • Straightness +/- .003”
  • Made in USA
  • from easton web site
looks like they are .003
 
Last edited:

TheTone

WKR
Joined
Mar 4, 2012
Messages
1,796
I’m sure I’m in the minority but I wish they were heavier gpi, closer to axis. I shot a previous discontinued 6mm that I loved mainly for the “standard” components
 

MattB

WKR
Joined
Sep 29, 2012
Messages
5,743
I would worry about durability based on the gpi specs. There is no free lunch.
 
  • Like
Reactions: Zac

TheTone

WKR
Joined
Mar 4, 2012
Messages
1,796
I like BE Spartans better because of the fact that it uses .204 nocks, so I can run IP5s.
I haven’t looked but I’d assume Easton has a nock bushing that will accommodate that. My previous 6mm shafts did
 
OP
D
Joined
Sep 28, 2018
Messages
2,233
Location
VA
I would worry about durability based on the gpi specs. There is no free lunch.
If you compare Eastons GPI to other manufacturers, they're very similar and probably true to advertisement. Easton's 5mm arrows are probably the heaviest 5mm out there

In my experience, Easton is VERY consistent in sticking to their GPI weight advertisement. I bought some other brand arrows and they were a full .7 grains heavier than advertised
 
Last edited:

JBrew

Lil-Rokslider
Joined
Jun 6, 2019
Messages
255
I've been shooting them for a couple months. No complaints, so far. I had a couple off shots at a recent TAC and they're still in good shape.
 

fordnut

FNG
Joined
Jul 4, 2016
Messages
71
b6d0eb26e2a30859b5fc63ae9e3cf4e4.jpg



Sent from my iPhone using Tapatalk
 
Top