Christensen issue?

[KCoop]

Hey folks, so i need some opinions. I have a Christensen Arms Ridgeline in 300wsm and it has what I can only assume an overly tight chamber. Since iv owned the rifle (new) I have had to wipe out the chamber with a cleaning patch on a brush every 20 round or so, or I start to show signs of over pressure (sticky bolt lift, ejector marks). I recently purchased 200 rounds of Nosler Trophy Grade 180s and it wont even chamber. A visual inspection shows a very slight difference in the shoulder area but this seems crazy to me. I contacted Christensen and they told me that their chambers are cut on the lower side of SAAMI spec and that is how they can achieve such good accuracy... The rifle has never been a fantastic shooter to begin with (~1.25MOA. ) So, here are my options; A. Rebarrel B. Have someone ream the chamber slightly. C Sell the rifle and put proceeds towards something else. Heres the kicker, the rifle needs a new stock as well. When I first purchased the rifle I took the stock off to clean and torque everything (like I do with every new rifle) and the stock between the mag box and trigger had a crack. I contacted Christensen at the time and they had told me that is was no big deal and that people will actually cut that part out... I was naive at the time and believed them. I'm kicking myself now for not making a big deal out of it and demanding a new stock. I say all that to say this, between a new stock, possibly a new barrel or having it reamed, Im pretty close to the cost of a new rifle. If I didn't like the 300WSM cartridge so much I would just walk away from it. Needless to say, I will never buy another Christensen. Do you guys have any thoughts?

 

[wind gypsy]

I'd make them make it right on the stock for sure and possibly the chamber.

I'd have a gunsmith confirm the chamber is within spec. I imagine having someone "clean up" the chamber to open it a bit could be done for quite a bit less than a full chamber job if you want to go that route.

There have been a handful of reports of nosler ammo not being within spec in recent years, i'd make sure that is good too.

 

[North61]

You can repair the stock..i wouldn't replace it epoxy can patch the crack. I'd take it to a good gunsmith and have them examine the chamber. If it's out of spec that gives you the ammunition to demand they make it right. If they won't come back here and make a stink.

 

[waspocrew]

Super common with CA rifles. Did CA say anything about opening up the chamber or is that on you?

I’d for sure want a new stock out of the deal from CA. Then decide if you really like the rifle. If not, sell and get a reliable rifle. My brother had a CA 300 WM - he had tight chamber issues too. While it shot well, he got tired of dealing with it and sold it.

 

[KCoop]

Super common with CA rifles. Did CA say anything about opening up the chamber or is that on you?

I’d for sure want a new stock out of the deal from CA. Then decide if you really like the rifle. If not, sell and get a reliable rifle. My brother had a CA 300 WM - he had tight chamber issues too. While it shot well, he got tired of dealing with it and sold it.

CA told me if I were to send it back in, they would check and see if it were within their specs but that was it. I should probably cause more of a fuss about the stock but I had the forend drilled for an addition 1/4-20 attachment and they make it well know any alterations void the warranty. Maybe I'm being pessimistic about it but Im thinking they're just going to tell me "to bad"

 

[HuntHarder]

Send it in. I doubt they would not take care of you. Overall, of the 4 I have owned, I had to send 1 back for a cracked stock. They took care of it, no issues. All of mine have shot really well.

 

[BRTreedogs]

Ship it back to them.

 

[Nockdown]

Send that POS in, let them fix it, then sell it. Had the same thing with a 28. Worst rifles ever.


Sent from my iPhone using Tapatalk

 

[pacoalcracker]

Send it back, make them repair what needs to be done, have them shoot it and send the report back to you. Shoot it yourself, if you are happy with it keep it. I have 2 CA FFT Ti rifles and both shoot very well without any issues. No complaints here. They will make it right.