Brass predicament…

Bater

WKR
Joined
Apr 2, 2020
Messages
588
Have a 243AI build that will be done this winter. Only probably I’m having is sourcing 243SRP brass. Peterson is the only quality brass manufacture that makes it as far as I know, and nobody has any in stock. I will continue to look for it but if I can’t find it what would be next best in your opinion? I run Alpha 260 SRP in my 260AI and it is phenomenal, just don’t know what issues I might run into necking it down to 243. I’d like to stay away from turning if it all possible.

Lapua LRP 243
Peterson LRP 243
Lapua SRP 260
Alpha SRP 260

What would you do?
 
I'd get LRP brass before necking down 260 brass. I typically get lapua when available but not sure how lapua and peterson 243 brass compare. I'd bet lapua has a little more capacity.
 
I'd get LRP brass before necking down 260 brass. I typically get lapua when available but not sure how lapua and peterson 243 brass compare. I'd bet lapua has a little more capacity.
Yeah I agree. I have a couple boxes of virgin Peterson 243 LRP and not sure if I want to pick up some Lapua LRP instead. Capacity differences doesn’t matter to me, primer pocket longevity is what I care about. Anybody have experience between Peterson/Lapua for primer pocket durability?
 
What is the purpose of your build?

Personally, I'd rather avoid necking down brass and would prefer a LRP with the case capacity of a 243AI if it's going to see cold weather use for a field/hunting rifle.
Just a backpack hunting mountain rifle for deer/bears here in the west. It will see plenty of freezing temperatures, but my 260AI (Alpha SRP) with CCI 450’s / H4350 has zero ignition issues in temperatures well below zero.
 
I don’t think you’ll see any difference between large and small rifle primers. Do you anneal and have tight chambers? Unless you’re trying to turn your 243ai into a 6UM, you’ll probably crack necks or get case head separation before primer pockets wear out. I’d just get 500 pieces of lapua LRP brass and call it good
 
Just a backpack hunting mountain rifle for deer/bears here in the west. It will see plenty of freezing temperatures, but my 260AI (Alpha SRP) with CCI 450’s / H4350 has zero ignition issues in temperatures well below zero.

On the ignition front, i'd be more worried about it with different (ball, double based) powders. I'm not an expert on it other than I know I've had hang fires with factory berger 6 Creedmoor SRP ammo in cold weather. I also recall hearing recently on a podcast with a primer/powder guru that undetectable hangfires happen and people never know because they are so incredibly short, but the milliseconds that ignition is further delayed also increases opportunity for POI displacement before the bullet is out of the barrel.
 
I don’t think you’ll see any difference between large and small rifle primers. Do you anneal and have tight chambers? Unless you’re trying to turn your 243ai into a 6UM, you’ll probably crack necks or get case head separation before primer pockets wear out. I’d just get 500 pieces of lapua LRP brass and call it good
Yeah I AMP every time before FL sizing. Yikes 500 pieces would last me five barrels! I’ve usually been good with 100 pieces of quality brass per barrel. My Alpha SRP 260AI is now on its 17th firing and the pockets are TIGHT. When you say that you don’t think I would notice a difference, are you talking about the durability of the SRP/LRP pockets?
 
OP, honestly, this seems like a case of over-thinking it. Most guys will burn out their barrels long before they blow out a primer pocket.

Also, primer pockets can be fixed
Well I’ve lost pockets in 5 or 6 firing with lesser brass, so it’s definitely a concern.
 
I guess it comes down to this then. Has anybody seen a primer pocket durability difference between Peterson/Lapua LRP standard bolt face brass?
 
Back
Top