88 TMK Loading Thread

[mwoolsey5]

Apologies in advance, I’m a complete amateur when it comes to hand loads and reloading still, but trying to learn. I plugged everything into an ai tool, but could someone verify I have the correct COAL length before I load some of these up.

22 CM
.120 Freebore
88 TMK
Hawkins Hunter DBM Short

Hawkins website says the Hunter DBM short magazine has an internal length of 2.880”. AI tool says the ideal length is 2.65-2.75” to touch the lands, but that I’m limited by the magazine and need to have a COAL of 2.5-2.52” to ensure smooth feeding and that the tip doesn’t drag in the mag. Does this sound correct or should I be loading up a dummy round at the longer COAL length to see how it see if it fits the mag and/or feeds well?

 

[43.6N]

View attachment 1044659
Apologies in advance, I’m a complete amateur when it comes to hand loads and reloading still, but trying to learn. I plugged everything into an ai tool, but could someone verify I have the correct COAL length before I load some of these up.

22 CM
.120 Freebore
88 TMK
Hawkins Hunter DBM Short

Hawkins website says the Hunter DBM short magazine has an internal length of 2.880”. AI tool says the ideal length is 2.65-2.75” to touch the lands, but that I’m limited by the magazine and need to have a COAL of 2.5-2.52” to ensure smooth feeding and that the tip doesn’t drag in the mag. Does this sound correct or should I be loading up a dummy round at the longer COAL length to see how it see if it fits the mag and/or feeds well?

Do you have the magazine on hand?
Make a dummy round of your chamber, and see how it fits in the mag.

 

[BlueJay]

Did some initial load development with 88gr TMKs today in my 22 Creedmoor with a 20" barrel. I had tried previous workup with 88 ELD-m and couldn't get them to group well. Loaded up Alpha LRP brass with the TMKs at 20 thousands off jam and Reloder 23 with three rounds at each charge weight (36 grains up to 39 grains in 0.5 grain increments). Everything over 36.5 charge weight shoot itty bitty groups; 39.0 grains had no pressure signs and an average velocity of 2880fps. Going to load up 30 rounds with 39.0 grains to get a better sense of the true dispersion but this looks really promising. This is a pretty new barrel so I expect it'll speed up.

 

[BBob]

22 CM
.120 Freebore
88 TMK
Hawkins Hunter DBM Short

Hawkins website says the Hunter DBM short magazine has an internal length of 2.880”. AI tool says the ideal length is 2.65-2.75” to touch the lands, but that I’m limited by the magazine and need to have a COAL of 2.5-2.52” to ensure smooth feeding and that the tip doesn’t drag in the mag. Does this sound correct or should I be loading up a dummy round at the longer COAL length to see how it see if it fits the mag and/or feeds well?

Post in thread 'The 22 creedmoor thread'

Thursday at 11:41 AM

That and I’ll add if you want an 88 ELDM specific freebore it’d be approximately .170”. That puts the shank ~.050” above the neck shoulder junction at touch and the OAL still has plenty of room to fit most all common magazines and boxes.

What would the OAL be with this specific freebore and the 88eld at touch

~2.770”

After a quick look with 88 TMK’s it’s pretty much the same. Base of the bullet shank in the neck with the TMK is pretty much the same as well. Basically an equal swap or near equal swap between the two 88’s.

• BBob

 

[AM_Hunter]

Ah yeah. Sorry I wasn’t clear that I was lining inside the necks with the Neolube.

No you were I just dont know how to read . Thanks for the input, gonna likely test out the loads tomorrow and hopefully not explode.

 

[SeanM243]

View attachment 1044659
Apologies in advance, I’m a complete amateur when it comes to hand loads and reloading still, but trying to learn. I plugged everything into an ai tool, but could someone verify I have the correct COAL length before I load some of these up.

22 CM
.120 Freebore
88 TMK
Hawkins Hunter DBM Short

Hawkins website says the Hunter DBM short magazine has an internal length of 2.880”. AI tool says the ideal length is 2.65-2.75” to touch the lands, but that I’m limited by the magazine and need to have a COAL of 2.5-2.52” to ensure smooth feeding and that the tip doesn’t drag in the mag. Does this sound correct or should I be loading up a dummy round at the longer COAL length to see how it see if it fits the mag and/or feeds well?

Not sure if you've already gotten your answer, I am running a .150 Freebore in my 22 Creedmoor and I am on the lands at 2.68 with the 88 TMK on a brand new barrel. I'm using those Hawkins SA standard magazines, in my 6 & 6.5 Creedmoors, they have no issues feeding ammo to 2.85 or so OAL. I did get my hands on the extended model for my 260 AI but full disclosure I have not tested it yet. You would be fine using that mag with a 22 Creedmoor.

 

[pods8 (Rugged Stitching)]

223rem 2.6” mags

For tikka
Waters are 2.6”
Mag3D has 2.55 & 2.68”

Aics
Waters 2.6”

There are a few aics at 2.5-2.55” that might able to be opened up to 2.6” easily

@longrangelead asked me to work on a longer mag to fit 6x45 or long 223/223AI. I started with the 3rd flush variant. I can feed 6x45 into my 223 (till it jams short). Needs more validation to call it good but promising start.

 

[mwoolsey5]

Do you have the magazine on hand?
Make a dummy round of your chamber, and see how it fits in the mag.

Not sure if you've already gotten your answer, I am running a .150 Freebore in my 22 Creedmoor and I am on the lands at 2.68 with the 88 TMK on a brand new barrel. I'm using those Hawkins SA standard magazines, in my 6 & 6.5 Creedmoors, they have no issues feeding ammo to 2.85 or so OAL. I did get my hands on the extended model for my 260 AI but full disclosure I have not tested it yet. You would be fine using that mag with a 22 Creedmoor.

Yeah I think it’s just going to be a bit of experimenting once I have the mag in hand. It’s currently at UM as they finalize the build, but should be headed my way shortly.

I’ll build a dummy round once I have it in hand to check fit and feeding, but sounds like it should be able to go to 2.7” if needed based on Sean’s response. Thanks guys. Looking forward to seeing what works best when all is said and done.

 

[Jfrog]

@longrangelead asked me to work on a longer mag to fit 6x45 or long 223/223AI. I started with the 3rd flush variant. I can feed 6x45 into my 223 (till it jams short). Needs more validation to call it good but promising start.
View attachment 1045232

Seeing those magazines in the works really makes the 6x45 seem like an interesting option for a rifle build…

 

[PC356]

Quick n easy work up on these green tip 88ers. Once fired Peterson LRP, BR2 primer, 38.8 gr H4350, 2.650 COAL. Tikka, 18” PBB .22 Creed. Loaded one to 39 gr, sharpied, chambered it to check for proximity to lands. Fired to check for pressure, nuthin. Backed off .2 and loaded 6 more, 1 for a sighter.
Done.