6 PRC reloading

[T_Widdy]

Could you give more info on the sac bushing I need. Was it a custom bushing

Sent from my SM-G986W using Tapatalk

Short Action Customs Neck Sizing Die Bushing 268 Diameter

Short Action Customs Neck Sizer Die Bushings have minimized neck runout in cartridge brass in nearly every die tested. After attempting to eliminate and...

www.midwayusa.com

These are what I use with Redding or Hornady dies.

 

[Odd1out]

Short Action Customs Neck Sizing Die Bushing 268 Diameter

Short Action Customs Neck Sizer Die Bushings have minimized neck runout in cartridge brass in nearly every die tested. After attempting to eliminate and...

www.midwayusa.com

These are what I use with Redding or Hornady dies.

Just to make sure. .268

Sent from my SM-G986W using Tapatalk

 

[T_Widdy]

Just to make sure. .268

Sent from my SM-G986W using Tapatalk

That’s what I use, it gets me to around .238” id. Then I use a .240 expander mandrel. If you want to run just a bushing and not expand, it would be around a .270 bushing depending on what neck clearance you want

 

[mlevimadden]

Anyone using ADG brass or is everyone using Lapua?

 

[Muledeerfanatic]

I am using Petersen and an FL Redding bushing die with a .270 bushing and a .2415 ish mandrel

 

[Odd1out]

I'm gonna bite on barrel do u think fb at .140 or .180 is better? Going with a 1 in 7.5 twist. Hoping to run 107 to 116s. I know above post talks about the freebore issue. But i believe it was just a 7 twist.

Sent from my SM-G986W using Tapatalk

 

[Schmo]

I'm gonna bite on barrel do u think fb at .140 or .180 is better? Going with a 1 in 7.5 twist. Hoping to run 107 to 116s. I know above post talks about the freebore issue. But i believe it was just a 7 twist.

Sent from my SM-G986W using Tapatalk

Go .180” FB with 7.5 twist

 

[Odd1out]

Its gonna be 22inch long if that matters also

Sent from my SM-G986W using Tapatalk

 

[Schmo]

Its gonna be 22inch long if that matters also

Sent from my SM-G986W using Tapatalk

Yeah, no need for 7 twist

 

[Odd1out]

Yeah, no need for 7 twist

Thx for the help

Sent from my SM-G986W using Tapatalk

 

[Odd1out]

Anyone reach out to say peterson or adg about making 6prc brass?

Sent from my SM-G986W using Tapatalk

 

[BigDog00]

Will a 6.5 PRC Forester Seater die work for a 6 PRC. I would think if I swapped the seater stem it should work.

 

[Frozenlead]

There’s a few guys that mentioned running the 6.5 dies and 6.5stem with no issues. Back around page 6. Nothing forester specific, but it shouldn’t be an issue.

 

[Judd]

I called Redding to get a 6 stem for my 6.5 die...guy said the stem should be deep enough that the 6 bullet wouldn't bottom out and to see how it did. It's been perfect...dude saved me some money and didn't just sell me a stem to sell me a stem. Hats off to Redding, not the first time they've done me right either.

 

[406Backwoods]

I’m gathering components for a 7 twist 6 Creed I’m having rechambered to PRC. Has anyone run the 95 TMK out of a 20-22” barrel? What speeds and powder?

 

[Titanmoose]

I got my first 30 rounds out. Using only 565, ADG brass 20” barrel PBB.

108 ELDM, 59 of 565 = 3067 and a great group SD/ES albeit not meaningful size. However 0 pressure signs in the slightest

I also shot a good group with Berger 109’s and 59 grains.

I had a smith give me some more freebore and sent 2 identical dummy rounds.

I think I ended up with WAY more FB than I expected. Maybe I’m wrong. I’m no smifff.

However seems like a lot more powder then other are using for same speed.

I’m thinking of going to 570 or 4831SC and seeing what I can get if going above 60 grains maxes out.

I have 59.5 to 61 at .5 intervals loaded

 

[Titanmoose]

The UM will give a little more velocity, but brass is only made by ADG, or else you have to use 6.5 SAUM brass. The 6 PRC gives terminal effectiveness to 850 -1,000 yards, and brass is super plentiful as 6.5 PRC. Single step neck dom

Did you ever try Grand? I have some next to my 4831sc and I’m trying to decide if I should load 10-15 up with grand and see what it can do.

 

[MT_Wyatt]

I got my first 30 rounds out. Using only 565, ADG brass 20” barrel PBB.

108 ELDM, 59 of 565 = 3067 and a great group SD/ES albeit not meaningful size. However 0 pressure signs in the slightest

I also shot a good group with Berger 109’s and 59 grains.

I had a smith give me some more freebore and sent 2 identical dummy rounds.

I think I ended up with WAY more FB than I expected. Maybe I’m wrong. I’m no smifff.

However seems like a lot more powder then other are using for same speed.

I’m thinking of going to 570 or 4831SC and seeing what I can get if going above 60 grains maxes out.

I have 59.5 to 61 at .5 intervals loaded

Would be interested to hear where you get with 570. 59g of 565 is where we landed on 6 PRC and I believe @Elk Chaser is right there with 25 PRC as well.

 

[406Backwoods]

Would be interested to hear where you get with 570. 59g of 565 is where we landed on 6 PRC and I believe @Elk Chaser is right there with 25 PRC as well.

I’ll be running 570 and 115 DTACS when I get my barrel back also. I’ll post results

 

[Titanmoose]

The UM will give a little more velocity, but brass is only made by ADG, or else you have to use 6.5 SAUM brass. The 6 PRC gives terminal effectiveness to 850 -1,000 yards, and brass is super plentiful as 6.5 PRC. Single step nec

Would be interested to hear where you get with 570. 59g of 565 is where we landed on 6 PRC and I believe @Elk Chaser is right there with 25 PRC as well.

I loaded up Grand last night from 55 to 59 grains.

Similar load data to H1000 bc there isn’t a whole lot of good comps.

So I have 565 from 59.5 to 61 loaded and th grand.

Fingers crossed one has something like 3150-3200 no pressure and great groups!! Maybe next weekend I’ll get out.