300 wsm 200.2 loads

[Jmort1754]

Staball 6.5

Anyone have some load data

I can go to 2.98 overall length

 

[doverpack12]

I’m using H4350 with 200.20x. I have two nodes about 150 fps apart.
Factory Tikka Superlite barrel cut to 20” with lower node 61.6 gr is 2715 fps and covers my needs so I run it there. 4 shots in the picture below, 1/2” dot.
2.2485” ogive which is 3.040” or just a few thousands under. I use the Hells Canyon mag for these, fits with room to spare. I’m about 0.060” off the lands but they were not picky. I shot 15, 30, 45 and 60 off, they all generally shot with a slight preference to 60.



Factory Tikka Superlite barrel cut to 20” with higher node 64.3 gr is 2847 fps shoots as well when I do my part.

RL16 might get more velocity than my loads but I had and use H4350 with several other rifles.

I did load this rifle with 6.5 Staball and Superformance using the Hammer 160 gr Tikka bullet and had incredible velocity, ok accuracy.
I now have a 154 Hammer HHT with H4350 load for close distance less than ideal shot angles.

 

[Cjackson51591]

I’m using H4350 with 200.20x. I have two nodes about 150 fps apart.
Factory Tikka Superlite barrel cut to 20” with lower node 61.6 gr is 2715 fps and covers my needs so I run it there. 4 shots in the picture below, 1/2” dot.
2.2485” ogive which is 3.040” or just a few thousands under. I use the Hells Canyon mag for these, fits with room to spare. I’m about 0.060” off the lands but they were not picky. I shot 15, 30, 45 and 60 off, they all generally shot with a slight preference to 60.

View attachment 1065654

Factory Tikka Superlite barrel cut to 20” with higher node 64.3 gr is 2847 fps shoots as well when I do my part.

RL16 might get more velocity than my loads but I had and use H4350 with several other rifles.

I did load this rifle with 6.5 Staball and Superformance using the Hammer 160 gr Tikka bullet and had incredible velocity, ok accuracy.
I now have a 154 Hammer HHT with H4350 load for close distance less than ideal shot angles.

If you don’t mind me asking what’s your 154 hht load.

 

[doverpack12]

If you don’t mind me asking what’s your 154 hht load.

67.8 gr H4350 from the same lot I’m loading the 200.20x with. I worked up to that.

 

[ZWA]

Sorry I missed this thread. Been playing around with the 200.20 in my 18” 300wsm. So far N560 has been looking good. Still trying to decide between the 200.20 and 185 Jugg for this season.

 

[Wrench]

 

[doverpack12]

Very close to wrench’s load above. 20” tikka Superlite Berger 200.20x, ADG, Fed 210M, going 2715 fps with H4350. I know it’s 3 shots and this is Rokslide but I don’t need anymore proof it shoots.

This is the exact same load that shot almost as well when the barrel was 24” previous seasons. Kampfeld cut it down and bushed to 5/8x24 and it just might shoot better…

Green dots are 1/2” across


Orange dot is 1/2” across with a single 180 Nosler Accubond factory shot aiming at the Orange. Green dot is 1/2” across with 2-200.20x in the same hole and same location as the first picture, shot above dot and to right are both Norma 180 Bondstrike.


I carry a mag with Norma or Nosler for close up less than favorable angle shots, and switch to an HCA mag with the 200.20x for anything at distance I dial.

 

[ZWA]

View attachment 1091260

Wrench what brass were you running? And thank you btw.