SRS all new Ti HUB to CB / banish

[Salmon River Solutions]

We just shipped a bunch of these HUB adapters off to Arizona for DLC coating and will have them back in about 2-3 weeks.

These are made from 6AL4V Ti.

Special introductory pricing of 20% off.

1.1 oz makes this the lightest on the market.

HUB TO CB / BANISH-BRAVO – Salmon River Solutions

www.salmonriversolutions.com

 

[ChrisAU]

Need some ultralight HUB direct thread mounts, any plans for the future? Flush fit with some feature to allow removal, the ones with hex ends look weird on a carbon barrel.

 

[Salmon River Solutions]

Need some ultralight HUB direct thread mounts, any plans for the future? Flush fit with some feature to allow removal, the ones with hex ends look weird on a carbon barrel.

Have you seen our CB Brake? we have spanner wrench holes on the backside of it for easy removal... These same holes could be used on a Direct Thread HUB mount. So then its the same spanner wrench, the entire HUB adapter shrinks in thickness by at least 3/16" of an inch, and can be round instead of a hex. That section is where a lot of weight is also so this would be lighter.

In the works next week for prototyping.

Ken

 

[Soj51hopeful]

I thought this was going to be about the Shawn Ryan show.

 

[ChrisAU]

Have you seen our CB Brake? we have spanner wrench holes on the backside of it for easy removal... These same holes could be used on a Direct Thread HUB mount. So then its the same spanner wrench, the entire HUB adapter shrinks in thickness by at least 3/16" of an inch, and can be round instead of a hex. That section is where a lot of weight is also so this would be lighter.

In the works next week for prototyping.

Ken

Awesome!

 

[StupidLightweight]

Well done, SRS. I will be getting one. If it's like your other products, this will be a fine addition to my Banish Backcountry.

 

[Andouille]

Well done, SRS. I will be getting one. If it's like your other products, this will be a fine addition to my Banish Backcountry.

Did you end up getting one for your Banish Backcountry? I'd like to know if there's sufficient clearance between the brake and the first blast baffle in the can.

 

[Salmon River Solutions]

Did you end up getting one for your Banish Backcountry? I'd like to know if there's sufficient clearance between the brake and the first blast baffle in the can.

Looks like its HUB. In that case it should work just fine.

Ken

 

[khuber84]

@Salmon River Solutions, Will you please make something like this to go onto an area 419 hellfire adapter? Or do they have that copyright patent protected?

 

[Salmon River Solutions]

@Salmon River Solutions, Will you please make something like this to go onto an area 419 hellfire adapter? Or do they have that copyright patent protected?

What specifically?

They make a bunch of them

Ken

 

[khuber84]

What specifically?

They make a bunch of them

Ken

Bravo to hellfire lefty connecter. Basically 1.375x24 to the LH hellfire muzzle mount. Prob the most popular option, followed by tbac cb to hellfire.

 

[T_Widdy]

Bravo to hellfire lefty connecter. Basically 1.375x24 to the LH hellfire muzzle mount. Prob the most popular option, followed by tbac cb to hellfire.

What’s wrong with the 419 ones?

 

[khuber84]

What’s wrong with the 419 ones?

Weight and price. have them on all 4 my cans, however options are always a good change.

 

[T_Widdy]

Weight and price. have them on all 4 my cans, however options are always a good change.

I have them too, they are expensive but I really like the system. I thought you might have had an issue with one.