Moose Mount Display

[Truaxdw]

What is everyone using to hang an alaska moose euro mount?

Take a look at dead on display

European Mount Skull Hanger | Skull Bracket

The most SECURE European Mount Skull Hanger System on the Market! Patented Interlocking bracket holds Cow, Moose, Buffalo, Elk, and Deer skulls just to name a few. We believe in being Secure, Discrete, and affordable! Our Skull Hangers are 100% made in the USA. "Show off your Trophy, not their...

www.deadondisplay.com

 

[william schmaltz]

Snare cable through the skull with a couple ferrules crimped on. The hook I used is a bit excessive, but this one is in the garage.

The guy that did my first moose bent large bolts and then attached to skulll from the inside with a locking nut. Then an eye bolt in the wall. I add safety cables to all my skulls in the house after a large earthquake we had about 5 years ago.

 

[roymunson]

Snare cable through the skull with a couple ferrules crimped on. The hook I used is a bit excessive, but this one is in the garage.

The guy that did my first moose bent large bolts and then attached to skulll from the inside with a locking nut. Then an eye bolt in the wall. I add safety cables to all my skulls in the house after a large earthquake we had about 5 years ago.

if you think your hook was excessive, you should see the 3/8" tapcon lags I used.

I spent too much time and effort to find out how a moose skull bounces.

 

[mikkel318]

We used a large lag screw with a washer welded on the end and I kept the lower jaw attached to lean it against the wall. Here is right as our place was getting finished.

 

[Robinhood21]

I've got the one on the floor on the wall now but I don't have a good picture of it.
2022 on Top
2024 on Bottom

 

[Joseph2186]

I really like the snowshoes and pelts do you have them zipped together? And are they just hanging on a screw or nail?

 

[Robinhood21]

I really like the snowshoes and pelts do you have them zipped together? And are they just hanging on a screw or nail?

I bought the snowshoes off ebay and screwed them together. Then just have the pelts hanging from small nails

 

[TheCougar]

 

[EMCaliber]

I opted for a european mount, to keep the look clean and I am happy with the result. I also debated a shoulder mount, but can't imagine how heavy and unwieldy it would have been. The skull and antlers was already a pain to lift.

 

[AK Troutbum]

Based on a couple recommendations from other sliders I went ahead and bought a 3D printed skull for a euro on my last moose. I tried to clean up the real skull but, ended up breaking the nose off in the process. The antlers are only 50’ish inches wide, and the fake skull is a little smaller than the natural one but, I think it looks okay. Now just need to figure out where it’ll hang.

Sent from my iPhone using Tapatalk

 

[buzzy]

Based on a couple recommendations from other sliders I went ahead and bought a 3D printed skull for a euro on my last moose. I tried to clean up the real skull but, ended up breaking the nose off in the process. The antlers are only 50’ish inches wide, and the fake skull is a little smaller than the natural one but, I think it looks okay. Now just need to figure out where it’ll hang.

Sent from my iPhone using Tapatalk

Looks nice. Who made the 3d printed skull. I’m looking at doing a similar thing for a couple of Spanish Ibex species but not sure where to get the reproduction skull from. Thanks

 

[AK Troutbum]

Looks nice. Who made the 3d printed skull. I’m looking at doing a similar thing for a couple of Spanish Ibex species but not sure where to get the reproduction skull from. Thanks

Thanks. That one came from Topo Skulls. I think they’re out of Utah. Two places were recommended, and I contacted both of them, but only Topo got back to me.


Sent from my iPhone using Tapatalk