LS Wild Suppressor Covers

[greyghostnw]

Those may be a little tighter in general. PM your order and I’ll send a looser one.

It also helps to get one edge and work it around.

Thanks for patience, we may suck occasionally but we’ll fix it.

I simply placed suppressor on bench end cap side down. Started wider end of cover over back of suppressor and worked full circumference of cover around suppressor so about 1/4” was on suppressor and shimmied it down to front of suppressor. Took less than 30 seconds. Fit is perfect.

 

[hereinaz]

That’s an easier way to pull it over.

The sewn end is folded and stitched so it doesn’t flare out. That makes it tight and less stretchy, so once you get it over, it slides easily.

The Raptor suppressors with the ribs for your hearing pleasure make it a bit of a pain though.

 

[JGRaider]

Those may be a little tighter in general. PM your order and I’ll send a looser one.

It also helps to get one edge and work it around.

Thanks for patience, we may suck occasionally but we’ll fix it.

That’s an easier way to pull it over.

The sewn end is folded and stitched so it doesn’t flare out. That makes it tight and less stretchy, so once you get it over, it slides easily.

The Raptor suppressors with the ribs for your hearing pleasure make it a bit of a pain though.

I wound up using the thin plastic sheet trick as shown by the OP to get mine on the Raptor 8. Worked great, love the tight fit. It ain't going nowhere which is the way I want it.

 

[Megalodon]

I'll be ordering one of these, look nice.

My $0.02 for everyone would be to do whatever they can to keep the cover from going past the end of their suppressor. It may seem like a trivial thing, but it overhanging too much can begin to impact bullet flight at longer ranges. I think Hornady uses angle of attack as the term to adjust for it in their ballistic solvers. It would be fine if it was the exact same every time, but that's not likely with a fabric cover.

 

[ChrisAU]

Those may be a little tighter in general. PM your order and I’ll send a looser one.

It also helps to get one edge and work it around.

Thanks for patience, we may suck occasionally but we’ll fix it.

I didn't have much time to work with it, let me try it again and if it just isn't doable I'll give ya a shout, thanks!

 

[Lonewolf72]

Got my covers today. They seem nice, light and trim...and seem to fit nicely. They should NOT slip under fire as the fit is VERY snug.

The covers for my Silencerco Omega 36M (green and gray) in long and short configuration slipped on easily if I slid the cover over the barrel, then pulled on to the can toward the muzzle.

The cover for my AB Suppressors A-10 was a bit more snug. It was more difficult to get started, but a little easier once the can was mounted. I had to twist the cover while simultaneously pushing toward the muzzle. The ribs on the can seemed to give a bit more friction, but I was eventually able to work it toward the end.

 

[KU_Geo]

Not seeing a way to order these on the website. How do I get a few ordered?

 

[coast range]

Not seeing a way to order these on the website. How do I get a few ordered?

He is re opening for orders here soon. These we all pre order.
I’m sure he will respond with specifics

 

[Scottyboy]

Not seeing a way to order these on the website. How do I get a few ordered?

Check his website on 4/21, as that’s when he said he is opening orders again.

 

[hereinaz]

Check his website on 4/21, as that’s when he said he is opening orders again.

Correct, 4/21

Thanks!

 

[hereinaz]

Got my covers today. They seem nice, light and trim...and seem to fit nicely. They should NOT slip under fire as the fit is VERY snug.

The covers for my Silencerco Omega 36M (green and gray) in long and short configuration slipped on easily if I slid the cover over the barrel, then pulled on to the can toward the muzzle.

The cover for my AB Suppressors A-10 was a bit more snug. It was more difficult to get started, but a little easier once the can was mounted. I had to twist the cover while simultaneously pushing toward the muzzle. The ribs on the can seemed to give a bit more friction, but I was eventually able to work it toward the end.

The AB seem to need a size larger because of the ribs. We will increase them a tiny bit.

Thanks for the feedback!

 

[bowrunner81]

I just received mine. It fits great and the quality is above its price point. Thanks

 

[hereinaz]

I just received mine. It fits great and the quality is above its price point. Thanks

Dangit, I should have charged more!

But seriously, thanks. I know we could have charged more, we are by far the least expensive solution. We wanted to make it affordable and charge a fair price.

It’s nice to have someone recognize it.

 

[JoeK]

Dangit, I should have charged more!

But seriously, thanks. I know we could have charged more, we are by far the least expensive solution. We wanted to make it affordable and charge a fair price.

It’s nice to have someone recognize it.

We all appreciate this bud ^

 

[Fatcamp]

Omega 300. Fits great.

 

[thinhorn_AK]

The one for my scythe showed up today. It fits great. There was no drama or weirdness when installing it. Once I got it over the lip, it just slid right on.

 

[coast range]

Right on time. Received my gun back from kampfelds yesterday to be threaded and suppressor cover showed up today. Fits great on an ultra 7. Thanks for awesome service once again

 

[thinhorn_AK]

I went out and shot 50 rounds through my 6.5 creedmoor/scythe rifle with the LS Wild cover I got in the mail yesterday.

It was great, I still got a little mirage but only after shooting 5-6 rounds so not something I’d worry about while hunting.

The thing hardly moved at all, I didn’t have to adjust it a single time through the 50 rounds. I can’t say that about any other cover I’ve used. It was awesome, I’ll be replacing all my covers with these once they are available for regular order. I should have bought more when I got this one.

I’m still not going to spend any money to protect my banish 30 though, I won’t even throw an old cover on it when I upgrade them all.

 

[greyghostnw]

Took 12 shots fairly quickly with .308 win to get enough heat in sight pic to be time to take a break. Without the cover it would’ve been 3 shots. Thats a massive improvement. Stayed in place entire time as well. Money well spent…

 

[huntinfool84]

Tried out the cover today, did great!! Shot a string of 13 without any mirage issues. Will be ordering more for the rest of my cans. Thanks for a great price on a great product!