Is it a bad idea to pull out?

[Caseknife]

Don't get a kinetic bullet puller, total PITA. Get one of these, https://grip-n-pull.com/, easy to use and have much more control over the process. Yes, you will need to resize the neck to get proper neck tension. Mono's like speed, I would use either the 130 or 150 TTSX and get closer to 2800-3000fps.

 

[cal30_sniper]

I do this quite often. It’s a 45 minute drive to the range, so I often take a large load ladder that I don’t get all the way up through before hitting pressure signs.

As one other said, it’s a really good idea to reset neck tension after pulling bullets. If you’re using a standard die, just back out the decapper enough that it won’t pop the primer out and run them through the sizing die again before re-charging and reseating the bullet. If you don’t do this, chances are you’ll end up with at least a few bullets than can be moved in the case by hand when you’re done.

Make sure the case is truly empty of powder before you recharge (sometimes static can cause pellets to cling inside the case). Also make sure you weight each charge as a unit from zero (measure out 44grs, don’t just add 1.0grs to the presumed 43grs of powder you pulled out).

 

[Tobe_B]

Don’t be dumb, shoot in the bum?

New tag line. I love it.

 

[Tobe_B]

I’d just shoot the rounds and reload new ones. Good trigger time.

 

[AM_Hunter]

@One300wsm I dont know why its not letting me directly reply to you but its the garmin Chrono. Its in line with my buddys speed too, hes shooting 44 gr out of 20" and getting about 2670.

I've got a whole extra 1". I constantly remind him about that too

​

 

[grfox92]

Trying to avoid the kids for a few more years, which means I should pull out?

I have 4 kids. Trust me. Pull out.

Sent from my SM-S931U using Tapatalk

 

[ColPenguin]

I would use a kinetic puller to pull them. It would not take long and I wouldn’t expect it to hurt the monolithic bullets.

A collet puller is so fast. It will not deform the bullet to an extent to noticeably affect accuracy of the load.

May depend on the specific kinetic puller. But I would think a collet puller would be much less chance of powder spill and waste, than a kinetic puller.

 

[Megalodon]

40 rounds is about a third of a quick range trip.

I don’t mean this to be offensive, but if you’re stressing over touching off 40 rounds I’m going to guess you could use the trigger time.

 

[North of 60]

Using a kinetic puller isn't that difficult and has collets for various diameter cases...and I probably lose more powder grains emptying my electronic powder scale after charging a bunch of cases and need to switch powders.

 

[BFR]

Definitely collet puller, easy and no chance of hammer breaking. Oh and not as noisy. I just did 40 rounds of test loads for my grandsons new rifle. No accuracy or just slower than other loads. I have an old RCBS press set up just for that and a dedicated quick change neck die set up for my Dillon 550.

 

[AM_Hunter]

@Megalodon Doesnt have anything to do with trigger time, I just dont want to use up $50 of components plus time to reload when I could be using those components and time working on creating a new dope for a new load.

 

[thinhorn_AK]

The pulled bullets will be fine.

Unless you break the tips off with that stupid hammer thing.

Just shoot what you have. I did the same thing a few years ago, had a few hundred rounds loaded up for my 30-06, they ahot great then I got a chronograph and saw they were like 2575 fps. I wanted more velocity so I made new ones that got me to 2700fps and shot even better.

I thought about pulling the bullets but I just kept using them, I even hunted and shot several animals with them and had no issues. Moving forward I use the new load.

 

[ReddingArcher]

I don’t know, I’ve found that once it’s loaded and ready to be shot, it’s almost impossible to pull out.