Inexpensive grinder?

[BRTreedogs]

One of my blades can absolutely go in backwards. I'll get a Pic later.

It can go in backwards.
But it would be a bevel against the flat.

It wouldn’t cut at all.
It mite smush thru the holes.

But it wouldn’t look like or be the consistency of ground meat at all.

 

[fmyth]

I bought a Vevor 1.5hp on Black Friday for $189. I have done 2 elk with it and am impressed.

 

[Xxjuiced]

Harbor freight probably has one

 

[ResearchinStuff]

It can go in backwards.
But it would be a bevel against the flat.

It wouldn’t cut at all.
It mite smush thru the holes.

But it wouldn’t look like or be the consistency of ground meat at all.

Bet.

 

[svivian]

Bet.

View attachment 941052

What brand is that so I know what not to buy

 

[realunlucky]

Bet.

View attachment 941052

I've never seen one like that either

Sent from my SM-S926U using Tapatalk

 

[realunlucky]

I bought a Vevor 1.5hp on Black Friday for $189. I have done 2 elk with it and am impressed.
View attachment 940954

That's a lot of horsepower for 200. Does vevor make attachments too?

Sent from my SM-S926U using Tapatalk

 

[ResearchinStuff]

What brand is that so I know what not to buy

Lem screw on dual grind. Cuts 2 plates at once, works great if you remember which way the auger turns and match the arrow up appropriately. If not, it is unfun.

 

[svivian]

Lem screw on dual grind. Cuts 2 plates at once, works great if you remember which way the auger turns and match the arrow up appropriately. If not, it is unfun.

Ahhh dual grind… never used one and yet makes sense on the design of the blade.

I think that clarifies some confusion on blade being backwards.

 

[fmyth]

That's a lot of horsepower for 200. Does vevor make attachments too?

Sent from my SM-S926U using Tapatalk

I don't know. I bought it to grind elk/deer meat. Looks very similar to a couple of the big brand names not sure if other manufactures attachments would work on it.

 

[coiloil37]

From the way some of you talk it’s pretty obvious to me you’re less selective on what’s in your mince then I am. From my experience, the finished product tastes better when EVERY piece of fat and connective tissue are removed from the edible meat. It also gives me a chance to run my eyes over it all to make sure I’ve gotten every hair or piece of debris.
I don’t care what any of you are doing but personally, I go through every single bit of meat and cut every muscle group down and remove everything that isn’t red meat. That leaves me with nothing but small pieces to grind. It also removes any possibility of bragging how I can process a full reefer van of deer in under a minute with my 600 hp, diesel powered, 7” diameter, quad bladed grinder that’s the single most important part of my hunting equipment.

Perhaps some of you will reconsider consider the quality of your finished product, most probably not. Ultimately, you do you and I’ll continue doing what I’m doing.

 

[antlerridge]

LEM 1 hp would be my go to


Sent from my iPhone using Tapatalk

 

[TimberHunter]

From the way some of you talk it’s pretty obvious to me you’re less selective on what’s in your mince then I am. From my experience, the finished product tastes better when EVERY piece of fat and connective tissue are removed from the edible meat. It also gives me a chance to run my eyes over it all to make sure I’ve gotten every hair or piece of debris.
I don’t care what any of you are doing but personally, I go through every single bit of meat and cut every muscle group down and remove everything that isn’t red meat. That leaves me with nothing but small pieces to grind. It also removes any possibility of bragging how I can process a full reefer van of deer in under a minute with my 600 hp, diesel powered, 7” diameter, quad bladed grinder that’s the single most important part of my hunting equipment.

Perhaps some of you will reconsider consider the quality of your finished product, most probably not. Ultimately, you do you and I’ll continue doing what I’m doing.

I do it a very similar way but it takes me like 8 hours to do a deer by myself so I’m going to be a bit less selective on what goes into the grinder to hopefully significantly reduce the amount of time it takes to cut it all up


Sent from my iPhone using Tapatalk

 

[BRTreedogs]

From the way some of you talk it’s pretty obvious to me you’re less selective on what’s in your mince then I am. From my experience, the finished product tastes better when EVERY piece of fat and connective tissue are removed from the edible meat. It also gives me a chance to run my eyes over it all to make sure I’ve gotten every hair or piece of debris.
I don’t care what any of you are doing but personally, I go through every single bit of meat and cut every muscle group down and remove everything that isn’t red meat. That leaves me with nothing but small pieces to grind. It also removes any possibility of bragging how I can process a full reefer van of deer in under a minute with my 600 hp, diesel powered, 7” diameter, quad bladed grinder that’s the single most important part of my hunting equipment.

Perhaps some of you will reconsider consider the quality of your finished product, most probably not. Ultimately, you do you and I’ll continue doing what I’m doing.

Pretty bold of you to determine what other men do with there meat.

Maybe some of just are not blessed with a super easy job and a ton of time off to leisurely play with our meat for hours.

But it sounds like you got it on easy street and have nothing better to do.

 

[Tmac]

I’ll echo the buy once cry once sentiment. I ran a little #8 sized on for a long time, did cows, deer, moose and elk with it. Upgraded to a Cabela’s (bass pro) 3/4hp #12 almost 10 years ago. Thing was an absolute game changer. No more chopping into cubes, just make it fit in the pile and it’ll grind it. Takes as long to clean up as it does to grind a deer. Also stuffs sausage casing almost too fast for one guy to keep up.

My older Cabela’s #12 is going strong for over 15 years. I think the older ones we have were Weston’s, but I am not sure. It’s been great for us. Lots of use.

The new Cabela’s/BassPro Carnivore line looks nice, but no idea who makes them. If mine dies before I do, I’ll get another known quality #12. I’m pretty invested in the #12 accessaries. The things pay for themselves with just a few animals.