Best contour for tikka t3x action

jtr1997

FNG
Joined
Apr 10, 2022
Messages
35
I have a tikka roughtech 6 5 prc that im going to redo into a 6.5 saum. Gun is in a stockys stock and id prefer not to have to open the channel. Im either going bartlien brux or Krieger steel barrel finished at 26. Anybody know what contours would best fit for me?
 
I have a tikka roughtech 6 5 prc that im going to redo into a 6.5 saum. Gun is in a stockys stock and id prefer not to have to open the channel. Im either going bartlien brux or Krieger steel barrel finished at 26. Anybody know what contours would best fit for me?

Unless you get a Tikka profile, you are going to have to open up the stock as almost all of the standard contour barrels from the major makers have a shank taper length longer than the factory Tikka contours.
 
Here are measurements of the Tikka D18 barrel profile for reference, which is fully free floated in the alpine and roughtec stocks, but I’ve always relieved them a bit on my guns…

IMG_1682.jpeg
 
Here are measurements of the Tikka D18 barrel profile for reference, which is fully free floated in the alpine and roughtec stocks, but I’ve always relieved them a bit on my guns…

View attachment 915815
Thanks ill check into it more. If I ordered a #3 or #4 sporter with a 1.250 shank diameter will it work or do i need a 1.15 shank? I may just have the stock opened up to a sendero in case I want to go carbon later.
 
I have a tikka roughtech 6 5 prc that im going to redo into a 6.5 saum. Gun is in a stockys stock and id prefer not to have to open the channel. Im either going bartlien brux or Krieger steel barrel finished at 26. Anybody know what contours would best fit for me?
Not to be "that guy"... but...might be worth putting a box through it. Give it a chance 😜

I shot my 6.5 creed ctr yesterday and my 140 bergers shot .5" and I was a bit dissapointed.

Ive got a tikka 300 mag i bought in 2018. Planned to rebarrel it just like you. It shot 1/2" groups with barely any work up so i rocked with it. I'm finally rebarreling it to a 25 prc. Hoping on the low recoil trend and it was getting annoying single feeding it 190 berger due to the shorter action length.

The tikka barrels are damned good. And 6.5 prc vs saum is pretty apples to apples.

Also...my new 25 prc barrel is pbb's tikka lite hybrid with all the flutes. Took em ~6 months Though. Was definitely expecting it sooner.

Fingers crossed it was worth the wait
 

Attachments

  • 20250802_140547.jpg
    20250802_140547.jpg
    137.8 KB · Views: 12
Thanks ill check into it more. If I ordered a #3 or #4 sporter with a 1.250 shank diameter will it work or do i need a 1.15 shank? I may just have the stock opened up to a sendero in case I want to go carbon later.
I’ve always done prefits for tikka 1.15. I know good smiths can turn down 1.25 standards no issue.

Truthfully. Most tikka and Sako barrels I’ve used have been as accurate and on average, lasted to higher round counts than most aftermarket barrels.
 
My
Not to be "that guy"... but...might be worth putting a box through it. Give it a chance 😜

I shot my 6.5 creed ctr yesterday and my 140 bergers shot .5" and I was a bit dissapointed.

Ive got a tikka 300 mag i bought in 2018. Planned to rebarrel it just like you. It shot 1/2" groups with barely any work up so i rocked with it. I'm finally rebarreling it to a 25 prc. Hoping on the low recoil trend and it was getting annoying single feeding it 190 berger due to the shorter action length.

The tikka barrels are damned good. And 6.5 prc vs saum is pretty apples to apples.

Also...my new 25 prc barrel is pbb's tikka lite hybrid with all the flutes. Took em ~6 months Though. Was definitely expecting it sooner.

Fingers crossed it was worth the wait
The barrel is almost used up. Not pulling a new barrel off of it. In was looking at a 25 prc also but think im going to run 6.5 saum not 100% decided on caliber yet but most likely 6.5 or 7 saum
 
My

The barrel is almost used up. Not pulling a new barrel off of it. In was looking at a 25 prc also but think im going to run 6.5 saum not 100% decided on caliber yet but most likely 6.5 or 7 saum

Ahh. There ya go!

Well I just got mine in

Pbb 23.25" 25 prc. Tikka light hybrid. Their new helical fluting.

Was expecting a thinner profile and lighter overall weight. I thought the pbb lite hybrid matched the tikka lite. I guess not.

It's 0.1 oz heavier then the 24.3" 300 mag barrel.

Looks sharp though!
 

Attachments

  • 20250804_192958.jpg
    20250804_192958.jpg
    199.7 KB · Views: 7
  • 20250804_204835.jpg
    20250804_204835.jpg
    252.2 KB · Views: 7
Ahh. There ya go!

Well I just got mine in

Pbb 23.25" 25 prc. Tikka light hybrid. Their new helical fluting.

Was expecting a thinner profile and lighter overall weight. I thought the pbb lite hybrid matched the tikka lite. I guess not.

It's 0.1 oz heavier then the 24.3" 300 mag barrel.

Looks sharp though!
Looks sharp. Im interested to see how it shoots. Im debating a prefit or having a Smith do it. If I went prefit I'd probably stay in the prc. I doubt the Sammi saum reamers would get the heavy bullets out far enough especially in a 7.
 
Back
Top