7 PRC load

[Gadjet]

I have a 7 PRC with a 20 inch barrel. I would really like to use the 180 grain ELDM. I know there have been threads about loading for this caliber, but I would like some opinions on loading for this particular bullet with the shorter barrel.
Thanks

 

[Jfowler]

I’m running 180 eldm’s with H1000 in my 22” barrel with good results.

 

[Slick8]

It sounds doable given the factor numbers listed above.

I don't have specific numbers as I don't yet own a PRC (on order) but I'll be starting with a 180 Berger Hybrid over H1k and 215s.

That's quickly become a popular combo for 20" PRCs and 180s to hit 2800.

Beyond that, perhaps some hens teeth (RL 26) or N565/570. Not a lot of personal experience personally, but they do out run H1k.

 

[Jfowler]

I also have tried N570. It was faster but not as accurate for me with that bullet. That’s in a savage ultralight.

 

[Lemhi]

I run an 18” but my buddies 20” runs 180 ELDM right at 2900fps with 4831SC. We both run the same load with great results, mine is just a bit slower of course.

 

[Slick8]

^^^^ Impressive!

 

[TheCoyote]

I also have a new 7mm PRC on order. I bit the bullet and purchased a Seekins PH3 from EuroOptic when the first became available. 26" barrel, i'm hoping to hit 3000fps with 175gn. ELD-Xs. Book data would indicate that 3000fps is overly optimistic but @Lemhi 's post gives me some encouragement.

I should mention that I do not have any of that Gold in a Bottle also know as Reloader's Powder....

 

[Gadjet]

I also have a new 7mm PRC on order. I bit the bullet and purchased a Seekins PH3 from EuroOptic when the first became available. 26" barrel, i'm hoping to hit 3000fps with 175gn. ELD-Xs. Book data would indicate that 3000fps is overly optimistic but @Lemhi 's post gives me some encouragement.

I should mention that I do not have any of that Gold in a Bottle also know as Reloader's Powder....

I would guess that you would be able to get pretty close to 3000 with the 26 inch barrel. Maybe with some N570.

 

[eoperator]

I recently wasted a whole bunch of time on a 21" 7prc. Started out hoping to run h1000/175eldx but accuracy suffered with this combo. Ended up shooting 8-10rnd groups each of;
H1000, n565, n570, r26 and a couple r23
175eldx,180eldm, 175eh 180hyb.

N570 upper 2900's fps was achievable if you want to deal with vibrating/compressed load. Accuracy and es was not good in my barrel.

-H1000 primers were flat at 2800fps, not great accuracy

-R26 with had good accuracy, 2900+fps and best average es

-N565 was the most accurate with all 4 bullets, decent es at about 2860fps

-R23 had low velocity and poor accuracy

Any combo of n565, r26 180eldm &175eh would be fine for my rifle. R26 has better velocity and es while n565 has the best accuracy.

 

[Gadjet]

The 2 powders that I have on hand are H4831SC and N565. Sounds like people are getting pretty good results with both.

 

[LawyerB]

I'm hoping to bring this thread back to life! I'm looking at buying a pre-fit Proof Carbon (20 inch) for my build, and I'm curious about the velocities that guys are getting.

 

[deerhunter628]

Im getting 2742 with H1000, 175 ABLR, new ADG brass, Fed 210 primer. Im shooting an UM custom Tikka with a 20” Ace barrel.