Browning X Bolt Barrel Threading for Suppressor

[UP NORTH]

Looking for some insight from guys that had tried threading an Xbolt for a suppressor. I know it’s been discussed a little.

Has anyone had success with getting the barrel threaded for a suppressor? The muzzle diameter is 0.615 at full barrel length (approx 21”). If I had it chopped to 18” I’d gain a little at 0.646”.

Looking at TBAC minimum OD barrel requirements I could only do 1/2x28 thread pitch.

I have the rifle up for sale. My thought was the barrel is too skinny and I could put the funds towards another rifle that would be suppressor ready. But it’s been difficult finding a buyer.

Any insight would be helpful.

 

[KenLee]

I have no input on the threading, but I'd just buy a new suppressor ready 18 inch barreled x-bolt for $11-1200 already cerakoated and ready to go.
Skip the might or might not hold up of cutting and threading what you have. Just my opinion.
Wish Browning sold that rifle in an 18 inch 7mm-08 along with the 6.5 CM and 308.

 

[UP NORTH]

I have no input on the threading, but I'd just buy a new suppressor ready 18 inch barreled x-bolt for $11-1200 already cerakoated and ready to go.
Skip the might or might not hold up of cutting and threading what you have. Just my opinion.
Wish Browning sold that rifle in an 18 inch 7mm-08 along with the 6.5 CM and 308.

I would like to go that route but need to sell this gun first. I love the xbolt and this one has been super accurate.

 

[KenLee]

I would like to go that route but need to sell this gun first. I love the xbolt and this one has been super accurate.

What caliber are you selling?

 

[Mighty Mouse]

I recently had two barrels threaded that measured approximately .580" at the muzzle (Browning A-Bolt 270 WSM and Savage Trophy Hunter 308 Win). Gunsmith trimmed both barrels back to about 18", cut 1/2-28 threads, then installed a 1/2-28 by 5/8-24 adapter. I've put a few rounds through both rifles with a direct thread 30 caliber suppressor on with no issues so far.

 

[UP NORTH]

What caliber are you selling?

6.5 CM

 

[KenLee]

6.5 CM

Aaah I recently bought a carbon medallion in 6.5 Creedmoor. Probably set for awhile on that round unless my son is interested. He's still a 243 fan after shooting them 27 years.
His only concern when he found out about the new Creedmoor was whether I was going to rob a scope off one of the old a-bolt 243s that I still have...and he occasionally runs off with.

 

[UP NORTH]

Aaah I recently bought a carbon medallion in 6.5 Creedmoor. Probably set for awhile on that round unless my son is interested. He's still a 243 fan after shooting them 27 years.
His only concern when he found out about the new Creedmoor was whether I was going to rob a scope off one of the old a-bolt 243s that I still have...and he occasionally runs off with.

243 is another great cartridge, I have one as well.

 

[atmat]

Don’t most Xbolts nowadays come threaded already for a brake? If it’s a 1/2” you can just get an adapter for cheap for your can.

 

[KenLee]

Don’t most Xbolts nowadays come threaded already for a brake? If it’s a 1/2” you can just get an adapter for cheap for your can.

I think he's wanting to lose at least 4 inches off the barrel so it's not so long when he adds the can.

 

[atmat]

I think he's wanting to lose at least 4 inches off the barrel so it's not so long when he adds the can.

That may be the case and I’d advise that. But he posted his measurements at the muzzle, too, so I thought he might be open to it.

 

[UP NORTH]

Don’t most Xbolts nowadays come threaded already for a brake? If it’s a 1/2” you can just get an adapter for cheap for your can.

Mine Xbolt is threaded and has a muzzle break. It’s a 2016 model so it’s metric, I believe M13x1.25.

My goal is to keep the overall length down, my suppressor that’s coming is 9” in length.

 

[UP NORTH]

I know they make adapters from metric to 5/8 x 24 but since I want it cut down my thought was might as well go 1/2x28.

 

[oklahunter]

I have a x-bolt in 25-06 that I had threaded by Thunderbeast for my suppressor 3 years ago. No issues. Give Thunderbeast a call.

 

[Andouille]

I have a 30-06 X-bolt with standard stainless barrel that's also a little thin for 5/8-24 thread, so I'm just going to have it chopped to 19" and threaded at 1/2-28. The thread below and an overall lack of actual, documented 1/2" thread issues gives me confidence that I'll not have any issues with thread failure.

1/2x28 Threaded 30 Cal Rifles - Suppressor Horror Stories

I have a tikka t3 lite in 300wsm cut to 21” and threaded 1/2x28. Have about 5-600 rounds through it. I’ve hunted with it a couple years with no issue, multiple day backpack style hunts. Can is griffin recce 7 16oz

rokslide.com