Search results

  1. C

    New Turkey Gun.......gimme your thoughts

    I built a turkey gun off a 20ga Yildiz youth over under. It has a selector switch and I choke one barrel for the normal 30-50 yard shots and the other barrel with IC for when one sneaks in too close. I run a red dot and #9 TSS handload a. The gun is very short and light. Sent from my iPhone...
  2. C

    16.5” .243 or 6.5CM?

    Yes, Harvester Evo. It has a serial number before the recall. Silencer Co took care of me with no issues and I was happy to deal with them and have a scythe sitting in jail. It was a 22” 300wm 1gr below Hornady book max. It was a perfectly clean separation at the weld, no jagged edges to...
  3. C

    16.5” .243 or 6.5CM?

    I honestly don’t know, it looks like it could have been a failed weld. I couldn’t find the rest of it to verify or rule out a baffle strike. It was scary though. Sent from my iPhone using Tapatalk
  4. C

    16.5” .243 or 6.5CM?

    To be honest my suppressor blew up shooting my 300wm not long after that post and I just received it back. That kinda but a damper on things. Sent from my iPhone using Tapatalk
  5. C

    Silencer Co Harvester with 300wm

    I’ll probably wait until I have the scythe. That way if something goes wrong I will not be without again. Sent from my iPhone using Tapatalk
  6. C

    Silencer Co Harvester with 300wm

    Thanks freaking scary, it honestly makes me scared to shoot this thing again in the 300wm. Worst is I have a Scythe Ti I’m waiting on that I purchased for this particular rifle. Sent from my iPhone using Tapatalk
  7. C

    Silencer Co Harvester with 300wm

    It is a Harvester Evo. It was direct threaded on a gun that had just been threaded. It was till tight when it happened. Obviously my first thought was a baffle strike due to a bad thread job. But this guy has a great reputation and I have verified the work with a rod by a third party. No issues...
  8. C

    Silencer Co Harvester with 300wm

    It was before the recall, not sure the manufacturer date but it was purchased in April of 22, I took possession in February 23. Sent from my iPhone using Tapatalk
  9. C

    Silencer Co Harvester with 300wm

    Well this is the issue, the original question was rhetorical. This happened to my Harvester after 3 shots with my 22” 300wm. It blew apart at the weld and I never found the other part. I don’t think it was a baffle strike because all three shots were in the bullseye. To be clear I am not...
  10. C

    Silencer Co Harvester with 300wm

    Has anyone put a significant number of 300wm rounds through a Harvester Evo? It is rated for 300wm with a 20” barrel I have 22” barrel pushing a a near max charge behind a 208gr eldm. I don’t see any pressure signs and am 1gr below book max. Is this something I need to be concerned about riding...
  11. C

    Rib mount for red dot

    I used a meadow creek for a 20ga O/U turkey gun. It worked great. Sent from my iPhone using Tapatalk
  12. C

    Burris FF 3-9x40mm Drop Eval Q&A

    I’m really looking forward to seeing this redone with different rings. Sent from my iPhone using Tapatalk
  13. C

    Sighting in a .22

    Damn, can’t find a RS1.2 and you are putting them on a .22lr. That looks like an awesome setup. Sent from my iPhone using Tapatalk
  14. C

    Q&A for SWFA SS 6x MQ Field Eval

    Form, would you mind explaining the information you are writing on these scope bodies. Thank you. Sent from my iPhone using Tapatalk
  15. C

    Suppressor wait times

    So all these quick approvals are all individual? If so that sucks because I have 2 I’m waiting on in single shot trusts. Sent from my iPhone using Tapatalk
  16. C

    Well I caved, down the hole I go….

    Those numbers seem higher than I expected. I know Improving gives additional powder capacity but does it change the pressures the gun can tolerate? Sent from my iPhone using Tapatalk
  17. C

    16.5” .243 or 6.5CM?

    I have not run it through the chrono yet. Will do that in the next couple days. Honestly just been playing with it seeing how it shoots. I started with 46gr of H1000 and saw no pressure signs. It shot 15 to around 1.3 MOA. Sent from my iPhone using Tapatalk
  18. C

    16.5” .243 or 6.5CM?

    I actually ended up getting the 1:8” .243 and the 6.5CM. Right now I am working on the .243 I have loaded the 108eldm to mag length with H1000 and it is showing a lot of promise. I only have a couple dozen rounds down the barrel right now but want to get a base line for MV with the load I am...
  19. C

    Robby's building a 6UM!

    What made you stop at 18”? Sent from my iPhone using Tapatalk
  20. C

    Videos, online resources for becoming a better rifleman.

    Did you ever pursue either of these classes? I’m in NC also and would like to find something local as well. Sent from my iPhone using Tapatalk

Latest posts

Featured Video

Stats

Threads
322,991
Messages
3,391,511
Members
75,112
Latest member
roll with the punches

Latest Articles

Top