Search results

  1. S

    Tikka T3 308 with 190 sub x"

    My barrel for my Tikka T3 arrives today from Kampfeld Customs after being cut down to 16.5" for my Nomad Ti XC. Just in time for hunting season, so I'll need to get on the ball and see if my loads have changed with the shorter barrel. But during this time, I go a notification about Trail Boss...
  2. S

    Suppressor for 16.5" 308

    My tikka T3 308 barrel should arrive at Kampfeld Customs today to get cut to 16.5" and add the shoulder adapter similar to this: Now I'm looking at cans. Really like the ratings on the enticer L-ti. Its a little longer than the S but even with that, I'm still damn near at the original length...
  3. S

    Trail Boss at Midsouth Shooters

    For those looking for some Trailboss powder for subsonic loads, midsouth shooters just sent me an alert. Picked up 2 containers.
  4. S

    Chop, thread with permanent adapter

    I've seen a few barrels that "appear" to have a bell at the end so that 5/8-24 threads can be used with direct mount. I'm considering chopping my Tikka low light setup to 16" and have this done. Here is a pic of what I'm talking about or something similar. Are these barrels turned down or is...
  5. S

    Rock Rive Arms rifles

    Am I missing something about RRA and their AR's? I have done a lot of searching and the only videos / information that I can find is about 9-13 years ago. Old data. I was looking at one of their predator pursuit uppers to mate up to my lower I have lying around. Some of their AR15 223 wylde...
  6. S

    Sold Magneto Speed Sporter

    I have a magneto speed sporter that's basically brand new. Wife bought me a Garmin, so it's no longer needed. Used it once for load development then again to compare readings to the Garmin. Load readings matched. It's all boxed up ready to ship, $75 shipped, paypal FF.
  7. S

    Powder dispenser for tuned beam scale

    Been working on this off and on in spare time but works fantastic. Tried a several designs but this one is the cats Azz. -Tuned RCBS 502 from Scott Parker (1 kernel of Varget sensitive. -Built powder dispenser with 2500 grain hopper -On/off power switch -Red start switch -Yellow bump /...
  8. S

    Reloading for AR15

    I'm going to start loading for my AR15 and was wondering about die sets. I see RCBS sells 223 die sets as well as small base die sets. Is the small base die set needed for my AR and if so, does using the small base die set effect anything if I were to use this ammo in a bolt 223? I ran across...
  9. S

    Anyone with a CTR or UPR running a AB Raptor Suppressor.

    I like the short barrel of my 20" CTR for our box stands. Looking at suppressors and I'm considering the AB Raptor due to the over-barrel section not adding alot of length. Weight isn't an issue for my because I'm not hiking with this rifle. If anyone has one and can comment, please do and...
  10. S

    Rcbs chargemaster or other dispenser info

    For those that have a rcbs chargemaster or any other type of powder dispenser, what is the rpm of the tube? When it's running up before it throttles back, need the speed.
  11. S

    Mtm case or other options

    I'm setting up my pelican case for travel. I loaded for my 7 mag and 308. Will probably bring both rifles. And 2 boxes of ammo each. I'm considering the 20 round MTM cases to store the ammo. My 7 mag rounds are longer than sammi spec by a good bit. What case do you guys recommend so my...
  12. S

    Kenton Turrets or custom turrets

    I just recently sold my 4-16x50 Credo Hx and I'm looking at the Tenmile 4-24x50. mainly looking at this particular model due to the reticle illumination. My Credo's entire reticle would illuminate rather than just the center dot of the Tenmile 4-24x50. The problem is Trijicon doesn't make a...
  13. S

    Sold Trijicon Credo Hx 4-16x50 Red center dot MOA C-2900001

    My other ad got messed up and wouldn't let me edit it, so killed it and started this one. Trijicon Credo Hx 4-16x50. The credo was mounted on my CTR and currently only has 5 shots on it. Looking to sell and get a 4-24x50 tenmile due to the illumination. It appears that the 4-24x50 tenmile has...
  14. S

    Sold Credo Hx 4-16x50 for Tenmile 4-24x50

    Trijicon Credo Hx 4-16x50. The credo was mounted on my CTR and currently only has 5 shots on it. Looking to sell and get a 4-24x50 tenmile due to the illumination. It appears that the 4-24x50 tenmile has just the center dot that will illuminate while the credo's entire reticle illuminates...
  15. S

    Seating depth and pressure

    I am by no means an expert but do understand, so I think, of how seating depth effects pressure. So please correct me if any of this sounds waaaayyyy off. 1) a bullet close or into the lands, depending on if close to max load, can and will produce pressure signs. Bullet doesn't get a running...
  16. S

    How much bearing surface is needed

    I'm looking to see if I can get a little more velocity out of my 20" CTR 308. Currently I'm using 155 scenar, 47.5g Varget, CCI-200, R-P brass, 2.810", 2840fps avg. This load shoots very well but is also a good bit compressed. I do however have 1lb of 8208xbr left and after talking to the...
  17. S

    Is 8208 XBR now a unicorn?

    I have just about 1 lb left and haven't seen it available in a year. Did they stop production on it, or is it just a fable unicorn that is unobtainable?
  18. S

    Any pheasant hunters here, surprised with trip to South Dakota

    I have been surprised with a Pheasant hunt to West River Haven in Gregory in early Oct of this year. At 51, I've hunted all sort of game but never pheasant. Long time duck, deer and dove hunter so bird shooting won't be an issue other than being startled when they jump up. My plan is to Bring my...
  19. S

    7mm Rem Mag vs the new age

    I want to hear from you guys to help me understand something. Last year, I started playing around with my older 7mag. Watched tons of videos and such about dealing with the belt, head spacing off the shoulder rather than the belt, bumping shoulder back, etc. Developed some very accurate loads...
  20. S

    Loose primer pocket fix question

    I have been following threads and watching videos on youtube about using the 1/2" - 5/8" ball bearing and a hardened bolt to tighten the primer pockets. I don't have any of my brass with loose pockets "YET", but I'm still trying to wrap my head around how this tightens the pocket. I would...

Latest posts

Featured Video

Latest Articles

Back
Top