I've got a PVA 3b Osprey on my Tikka and the shank measures 1.145". This one was ordered several years ago though, back in 2021 if I remeber correctly. Seems they run a bit thicker at the shank than factory for sure.
I worked up some loads for my 6CM with Peterson LRP brass, so not a perfect comparison. It's a Tikka with an 19" Osprey barrel, 1-7" twist.
Using Perterson LRP, H4350, CCI-BR2s, and 108 ELDMs kissing the lands, .005" jump. Below were my results:
40.8 gr - 2892 fps, no pressure signs
41.1 gr...
My 6.5 PBB has right at 1,200 rounds down it now. I did a 25 round group over the coarse of a few hours, just out of curiousity. It's still shooting well. This is their #2 contour, not a hybrid lite but good data nonetheless.
Should be fine with a BDL set up, not sure on the DBM set up, that may take some tweaking. Gunsmith buddy has a .308 barrel on an old 700 LA that was a 30-06. It feeds fine with a standard follower plate, so you could go BDL worst case. There are a few options these days for BDL that fit an...
I've got both the M50 and the VG2. I've had the M50 for about 4-5 years, it was their 1st gen that was actually made by AG composite, not that the ergos' have changed at all. I have very much enjoyed it.
The grip/palm-swell and trigger reach are perfect, for me. I think the Gen 2 version...
Good looking rifle. You should be fine with an 18", they seem to do well from a short barrel.
My 19" 6cm velocities are:
Lapua SRP and H4350
103 ELDx at 2900 (range load)
103 ELDx at 3030 (hunting load)
Peterson LRP and H4350 loads:
105 BTHP at 3000
108 ELDm at 2995
Whack the crap out of it with a rubber mallet, that helps break up the "carbon lock" that has siezed up on the threads. This was advice I got directly from Thunderbeast years ago.
The "original" Gamekings work just fine. Killed a good many with a .243/100gr SGK and a .270/130 SGK. Probably 1500+/- pigs and deer over about 40 years. No limits on deer (in season) and pigs here in SC so it accomadates a good bit of experimenting.
High shoulder will be DRT, pass...
I've not seen an option other than the Hanson Bros, previoulsy mentioned. I have thought about going that route but I've been hesitant as supposedly the ports on the Tbac CB act as a "sacrificial" baffle for the can.
Also, for the "direct thread" option on a Tbac, pretty sure I read that all...
I used Peterson brass for the first time yesterday, 6mm CM LRP. Very good intial impressions, seems like great brass and on par with my Lapua baseline data. Accuracy was excellent on the virgin brass, gtg in my book. Extra points for the nice packaging as well. I see more in my future.
Its...
In my old Rem 700, 7-08 that had a 22" Bartlein, I used Varget with the 162 Amax.
Ended up at 39.5 grains at 2630 fps. I worked up to 41.0 grains at 2720 and it shot good, just better at the lower node.
I've used the 140 Accubond and 150 Ballistic tips a good bit, both worked great at those ranges. The 150 BT may be the most overlooked 7mm bullet out there, they are great bullets for deer. The BC isn't great but for 400 and in no problem, as you noted.
If you can find them, the 120 BT is a...
I've loaded them a good bit and they kill just fine. I switched to the 140 ballistic tips (mainly because of availability) and my impressions are the 140's tend to produce more consistent "bang flops", so to speak. But I would never feel "undergunned" with the 120 BTs on deer sized game at...
3b that they contoured down to the Tikka OD at the shank. It looks pretty similar to a friends CTR, to my eye, but I haven't taken any comparision measurements.
I just put a 6mm creed barrel on my Tikka, Osprey 1-7 twist at 19". Initial load testing with H4350 and 103 ELDx looks good. Worked up to 3100, where I hit pressure signs. The accuracy nodes appear to be at 2900 and 3050, either will be plenty for my needs.
Loaded up some 103 ELDx for testing in my new 6mm creedmoor barrel. Osprey, 1-7 twist, finished at 19" on my Tikka. I was pleasantly suprised at the speeds I got with the short tube.
Osprey 3b contour, looks very similar to a CTR profile from what I can tell. They turn the shank down...